Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
The cause and effect of this title should be reversed, because I want to adjust the timer interrupt of the microbit main control board, and seek answers on the Internet. Finally, I learned that the mo...
After we made a buzzer together last time, your brain circuits were very fast. Now let's strike while the iron is hot and think about it. In the past, we have been using digital pins (such as D0, D1, ...
I have seen many big factories, such as Jiali Chuang, and they basically charge 100 yuan more for black paint (compared with green paint). I have also asked some small board factories, and their green...
[b][size=5]To compile the image file for the SINA33 development board, you need to build a cross-compilation environment first. For this environment, you can refer to the previous document "How to cre...
[size=6]Design of GPS Positioning System Based on MSP430 LCD Display[/size] [size=6]File includes: program, schematic diagram, module introduction, module purchase address! The title of the graduation...
There are two IEEE addresses in CC2530/CC2538/CC2630, one is called Primary IEEE address, the other is called Secondary address. Primary IEEE address is stored in Information Page of chip, this addres...
0 Introduction
With the development of economy, people's demand for anti-theft, anti-robbery and fire prevention security equipment is growing, and the alarm system has also developed from the ...[Details]
1.
Advantages of
OLED
1. The thickness can be less than 1 mm, which is only
1/3 of the
LCD
screen, and the weight is also lighter;
2. Solid-state structu...[Details]
Sina Digital News reported on the morning of February 4 that investment bank JP Morgan Chase (JP Morgan) analyzed that the rumored Apple virtual reality (VR) device may be released in the first...[Details]
The "streaming media rearview mirror" that uses cameras and display screens instead of the interior rearview mirror has become an important configuration for many luxury and independent brands to fla...[Details]
NVIDIA will officially release the GTX 1660 Super graphics card next week? According to VCZ, the evaluation sample card is already on the way and will soon reach the hands of the media. Three day...[Details]
Taking the epidemic as an order - in 5 days, Wuhan Huoshenshan Hospital was powered on; in 4 days, Henan "Xiaotangshan" power grid project was completed; in 3 days, the power "lifeline" of Wuhan Le...[Details]
1. When the power is off, measure in the ohmmeter mode, use the red and black test leads to test the live wire and the ground wire. If the meter shows low resistance, it means there is a short circui...[Details]
Overview of the four gases in the conventional four-in-one gas detector: 1. Values of different concentration ranges of combustible gas methane: 1. Methane (CH4): The gas detector alarms when it ex...[Details]
Mobile devices are becoming an integral part of our daily lives. Take smartphones, for example. In addition to simple phone calling, smartphones now have rich features that support social networkin...[Details]
Recently, Weihua Technology (TWSE: 3055), a professional brand of semiconductor packaging and testing solutions, and its partner NI jointly announced that they have successfully built a complete RF t...[Details]
At present, the global medical electronics industry is gradually showing an attractive development prospect, and the speed of product replacement is constantly increasing. At the same time, due to ...[Details]
Consumers' understanding of joint venture brand models generally remains in the aspects of "big brands, stability, value preservation, etc." and they do not pursue much pursuit of the intelligence as...[Details]
introduction
Monitoring technology plays a vital role in the security of political, industrial and cultural facilities. The monitoring system is an important part of the security system. It has...[Details]
Last night, Chen Jin, general manager of Lenovo China's mobile phone business unit, hinted during an interaction with netizens that Lenovo will restart the Lemon brand. Earlier, Chen Jin also said ...[Details]
The last line after startup prompts can't access tty, job control turned off, which means that the console cannot be entered. The reason is that there is a problem in the /etc/inittab file
Sol...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
