115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Features
Applications
Best acceleration sensitivity of 0.1 ppb/g
Any frequencies between 115.2 MHz and 137 MHz accurate
to 6 decimal points
100% pin-to-pin drop-in replacement to quartz-based XO
Excellent total frequency stability as low as ±20 ppm
Industry best G-sensitivity of 0.1 PPB/G
LVCMOS/LVTTL compatible output
AEC-Q100 qualified
5-pin SOT23-5 package: 2.9 x 2.8 mm x mm
RoHS and REACH compliant, Pb-free, Halogen-free and
Antimony-free
Contact SiTime
for up-screening and LAT programs
Avionics systems
Field communication systems
Telemetry applications
Electrical Characteristics
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and nominal supply voltage.
Parameters
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
115.20
-20
-25
-30
-50
Operating Temperature
Range (ambient)
T_use
-40
-40
-40
-55
Acceleration (g) sensitivity,
Gamma Vector
Supply Voltage
Current Consumption
F_g
–
Typ.
–
–
–
–
–
–
–
–
–
–
Max.
137
+20
+25
+30
+50
+85
+105
+125
+125
0.1
Unit
MHz
ppm
ppm
ppm
ppm
°C
°C
°C
°C
ppb/g
AEC-Q100 Grade 3
AEC-Q100 Grade 2
AEC-Q100 Grade 1
Extended cold, AEC-Q100 Grade1
Low sensitivity grade; total gamma over 3 axes; 15 Hz to 2 kHz;
MIL-PRF-55310, computed per section 4.8.18.3.1
All voltages between 2.25V and 3.63V including 2.5V, 2.8V, 3.0V and
3.3V are supported.
Contact SiTime
for 1.5V support
No load condition, f = 125 MHz, Vdd = 2.25V to 3.63V
No load condition, f = 125 MHz, Vdd = 1.62V to 1.98V
Condition
Refer to Tables 14 to 16 for the exact
list of supported frequencies
Inclusive of Initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply voltage
and load (15 pF ± 10%).
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Rugged Characteristics
Supply Voltage and Current Consumption
Vdd
Idd
1.62
2.25
–
–
Duty Cycle
Rise/Fall Time
Output High Voltage
DC
Tr, Tf
VOH
45
–
–
90%
1.8
–
6
4.9
–
1.5
1.5
–
1.98
3.63
8
6
55
3
2.5
–
V
V
mA
mA
%
ns
ns
Vdd
Vdd = 2.25V - 3.63V, 20% - 80%
Vdd = 1.8V, 20% - 80%
IOH = -4 mA (Vdd = 3.0V or 3.3V)
IOH = -3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOH = -2 mA (Vdd = 1.8V)
IOL = 4 mA (Vdd = 3.0V or 3.3V)
IOL = 3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOL = 2 mA (Vdd = 1.8V)
Pin 1, OE
Pin 1, OE
Pin 1, OE logic high or logic low
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
Input Characteristics
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
–
–
100
–
30%
–
Vdd
Vdd
k
Rev. 0.5
July 22, 2019
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Table 1. Electrical Characteristics
(continued)
Parameters
Startup Time
Enable/Disable Time
Standby Current
Symbol
T_start
T_oe
I_std
Min.
–
–
–
–
Typ.
–
–
2.6
1.4
Max.
5.5
130
–
–
Unit
ms
ns
A
A
Jitter
RMS Period Jitter
RMS Phase Jitter (random)
T_jitt
T_phj
–
–
–
–
1.6
1.8
0.7
1.5
2.5
3
–
–
ps
ps
ps
ps
f = 125 MHz, 2.25V to 3.63V
f = 125 MHz, 1.8V
PRELIMINARY
Condition
Measured from the time Vdd reaches its rated minimum value
f = 115.20 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles
Vdd = 2.8V to 3.3V,
ST
= Low, Output is weakly pulled down
Vdd = 2.5V,
ST
= Low, Output is weakly pulled down
Startup and Resume Timing
f = 125 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
f = 125 MHz, Integration bandwidth = 12 kHz to 20 MHz
Table 2. Pin Description
Pin
1
2
Symbol
GND
NC
Power
No Connect
Output Enable
3
OE/NC
No Connect
4
5
VDD
OUT
Power
Output
Functionality
Electrical ground
[1]
No connect
H
[2]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
Any voltage between 0 and Vdd or Open
[2]
: Specified
frequency output. Pin 3 has no function.
Power supply voltage
[1]
Oscillator output
NC
2
Top View
GND
1
5
OUT
YXXXX
OE/NC
3
4
VDD
Figure 1. Pin Assignments
Notes:
1. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
2. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 3 is not externally driven. If pin 3 needs to be left floating, use the NC option.
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[3]
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Table 4. Thermal Consideration
[4]
Package
SOT23-5
Note:
4. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
JA, 4 Layer Board
(°C/W)
421
JC, Bottom
(°C/W)
175
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
85°C
105°C
125°C
Maximum Operating Junction Temperature
95°C
115°C
135°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Rev. 0.5
Page 2 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
PRELIMINARY
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 0.5
Page 3 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Test Circuit and Waveform
Test
Point
Vout
Vdd
PRELIMINARY
tr
5
4
0.1µF
Power
Supply
tf
80% Vdd
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
15 pF
(including probe
and fixture
capacitance)
1
2
3
Vdd
1k
OE/ST Function
Figure 2. Test Circuit
[6]
Note:
6. SiT2045 has “no runt” pulses and “no glitch” output during startup or resume.
Figure 3. Waveform
[6]
Timing Diagrams
Vdd
90% Vdd
Vdd
50% Vdd
T_oe
No Glitch
during start up
Pin 4 Voltage
T_start
OE Voltage
CLK Output
HZ
CLK Output
HZ
T_start: Time to start from power-off
T_oe: Time to re-enable the clock output
Figure 4. Startup Timing (OE Mode)
[7]
Figure 5. OE Enable Timing (OE Mode Only)
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 6. OE Disable Timing (OE Mode Only)
Note:
7. SiT2045 has “no runt” pulses and “no glitch” output during startup or resume.
Rev. 0.5
Page 4 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
@ lugl4313820【Renovation of old things】Graffiti lamp 1 Material preparation
【Renovation of old things】 Graffiti lamp 2 software preparation
【Renovation of old things】 Finished product of graffiti desk...
Source: Science and Technology Daily reporter Fu YifeiRecovery and landing is the final stage of a manned spacecraft mission and determines the ultimate success or failure of the mission. In order to ...
Buck - boost chargers have become increasingly popular in recent years because they can charge a battery from nearly any input source, whether the input voltage is above or below the battery voltage.
...
The Netherlands hacker camp MCH2022, which will take place on July 22, will feature the MicroPython programmable badge below. It has an ESP32 and a Lattice FPGA with a color display.https://mch2022.or...
On September 15, the US ban on Huawei's chip supply chain officially came into effect. The ban stipulates that chip manufacturers using US equipment, software and designs are prohibited from shipping...[Details]
Recently, Bloomberg New Energy Finance (BNEF), a world-renowned research institution, released the Energy Storage System Cost Survey 2023 (hereinafter referred to as the "Report"). In its energy st...[Details]
In the instrument we designed, we used PIC series microcontrollers and encountered the problem of floating point operation. After consulting the relevant information, we found that the format of its f...[Details]
The timer counts on-chip clock pulses, and the counter counts external pulses. The 51 microcontroller has two 16-bit timers/counters: timer 0P3.4 and timer 1 P3.5 3.0 RXD serial port input 3.1TXD 3...[Details]
Embedded Programmable Controller and Its I/O Module
In order to reasonably solve the problems in the current software and hardware allocation of the programmable logic controller itself, as wel...[Details]
The T1 16-bit timer of M16 has a total of 15 working modes. The other two 8-bit timers (T0/T2) are relatively simple, except that T2 has an asynchronous working mode for RTC applications
...[Details]
(1) Define the initial entry point of the code: The initial entry point refers to the starting point when the code is running. It is unique in each image file and must be contained in each executable...[Details]
On August 17, the EU’s New Battery Law (2023/1542) issued by the European Commission in July will officially come into effect. After a nearly three-year primary legislation process, this regulation i...[Details]
1. Door head LED strip screen
The LED strip screen on the door head has strong dynamics and bright colors, which can attract attention. It is mainly used to publish the latest advertising info...[Details]
Mechanical mud density meters need to be tested for discrimination, which is also called sensitivity limit. It mainly checks the integrity of the knife edge and knife bearing of the mechanical mud den...[Details]
Sunny Optical released the shipment status of the company's various products in April. According to the announcement, optical parts are still the business with the strongest growth potential of Sunny...[Details]
Due to the continuous improvement of performance requirements, especially the increasing call for "green" power supplies, modern inverter systems have higher requirements for power factor correctio...[Details]
Definition of Bandwidth Bandwidth has many application areas. It can be used to identify the data transmission capacity of signal transmission, the amount of data passing through the link per uni...[Details]
I have been crazy about various microcontrollers recently. I have been looking at AVR microcontrollers recently and found that in addition to FALSH and SRAM, there is also an on-chip EEPROM in the mic...[Details]
1 Main technical indicators of regulated current power supply
(1) Output current range The output voltage of a single-phase AC regulated power supply is usually fixed at 220V. Some p...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
