EEWORLDEEWORLDEEWORLD

Part Number

Search

ASM3P2769AG-08TT

Description
Low Power Peak EMI Reducing Solution
CategoryThe embedded processor and controller    Microcontrollers and processors   
File Size134KB,10 Pages
ManufacturerON Semiconductor
Websitehttp://www.onsemi.cn
Environmental Compliance
Download Datasheet Parametric View All

ASM3P2769AG-08TT Overview

Low Power Peak EMI Reducing Solution

ASM3P2769AG-08TT Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerON Semiconductor
Parts packaging codeSOIC
package instructionTSSOP, TSSOP8,.25
Contacts8
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresALSO OPERATES WITH 2.5V SUPPLY AT 12MHZ
JESD-30 codeR-PDSO-G8
length4.4 mm
Number of terminals8
Maximum operating temperature70 °C
Minimum operating temperature
Maximum output clock frequency13 MHz
Package body materialPLASTIC/EPOXY
encapsulated codeTSSOP
Encapsulate equivalent codeTSSOP8,.25
Package shapeRECTANGULAR
Package formSMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply2.5/3.3 V
Master clock/crystal nominal frequency13 MHz
Certification statusNot Qualified
Maximum seat height1.1 mm
Maximum slew rate0.01 mA
Maximum supply voltage3.6 V
Minimum supply voltage2.7 V
Nominal supply voltage3.3 V
surface mountYES
technologyCMOS
Temperature levelCOMMERCIAL
Terminal formGULL WING
Terminal pitch0.65 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
width3 mm
uPs/uCs/peripheral integrated circuit typeCLOCK GENERATOR, OTHER
ASM3P2769A
Low Power Peak EMI
Reducing Solution
Description
The ASM3P2769A is a versatile spread spectrum frequency
modulator designed specifically for a wide range of clock frequencies.
The ASM3P2769A reduces electromagnetic interference (EMI) at the
clock source, allowing system wide reduction of EMI of all clock
dependent signals. The ASM3P2769A allows significant system cost
savings by reducing the number of circuit board layers, ferrite beads
and shielding that are traditionally required to pass EMI regulations.
The ASM3P2769A uses the most efficient and optimized
modulation profile approved by the FCC and is implemented by using
a proprietary all digital method.
The ASM3P2769A modulates the output of a single PLL in order to
“spread” the bandwidth of a synthesized clock, and more importantly,
decreases the peak amplitudes of its harmonics. This results in
significantly lower system EMI compared to the typical narrow band
signal produced by oscillators and most frequency generators.
Lowering EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation.’
Applications
http://onsemi.com
TSOT−6
O SUFFIX
CASE 419AF
TSSOP−8
T SUFFIX
CASE 948AL
SOIC−8
S SUFFIX
CASE 751BD
PIN CONFIGURATIONS
1
PD
XOUT
XIN / CLKIN
VSS
ModOUT
VDD
The ASM3P2769A is targeted towards all portable devices with
very low power requirements like MP3 players and digital still
cameras.
Features
6−Pin TSOT−23 Package
(Top View)
1
Generates an EMI Optimized Clock Signal at the Output
Integrated Loop Filter Components
Operates with a 3.3 V / 2.5 V Supply
Operating Current less than 4 mA
Low Power CMOS Design
Input Frequency Range:
6 MHz to 12 MHz for 2.5 V
6 MHz to 13 MHz for 3.3 V
Generates a 1X Low EMI Spread Spectrum Clock of the Input
Frequency
Frequency Deviation:
±1%
@ 10 MHz
Available in 6−pin TSOT−23, 8−pin SOIC and 8−pin TSSOP
Packages
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
XIN / CLKIN
XOUT
PD
NC
VDD
NC
ModOUT
VSS
8−Pin SOIC and TSSOP Packages
(Top View)
KEY SPECIFICATIONS
Description
Supply Voltages
Cycle−to−Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
VDD = 3.3 V / 2.5 V
200 pS (Max)
45/55%
F
IN
/256
±1%
@ 10 MHz
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
©
Semiconductor Components Industries, LLC, 2011
August, 2011
Rev. 3
1
Publication Order Number:
ASM3P2769A/D
USB2.0 related
Sorry, I can't do it again The following figure is the previous solution, only when the device is in USB2.0 high-speed mode:The following figure plans to use the STM32 USB peripheral, OTG mode:If you ...
呜呼哀哉 Analog electronics
The dark current of the low-power wake-up button of the vehicle TP exceeds the standard
Dear experts, I am working on car TP. Recently, a project has a screen-off wake-up function. A low-power button is specially designed to achieve this function. It is required that the current flowing ...
Arnorelax Automotive Electronics
Selling Ti DSP development board
USB5410, PCI interface emulator, 6201 board. Available in a package for 900 RMB. You can search for "TI DSP development board" on ZhuanZhuan....
hanguofu Buy&Sell
[GD32E231 Work Submission] Quartz Accelerometer Acquisition
IntroductionThe quartz accelerometer is a high-precision acceleration sensor with a higher range and stability than MEM. It can be combined with various gyroscope systems to achieve high-precision att...
wolfg4 GD32 MCU
5G is coming, 4G speed is slowing down? Learn about load balancing link aggregators
A new, simple, rough and easy-to-understand way (you can break the sentence here) to analyze the needs of an electronic product - load balancing link aggregator! 5G is coming. If you are still using 4...
Jacktang RF/Wirelessly
TE Welfare Month|Rewarded surveys, technical tips, limited-time discounts
TE Welfare Month is now open! Here you can not only get technical knowledge, but also participate in prize-winning activities and enjoy limited-time discounts! What are you waiting for? Come and get y...
EEWORLD社区 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号