115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Features
Applications
Best acceleration sensitivity of 0.1 ppb/g
Any frequencies between 115.2 MHz and 137 MHz accurate
to 6 decimal points
100% pin-to-pin drop-in replacement to quartz-based XO
Excellent total frequency stability as low as ±20 ppm
Industry best G-sensitivity of 0.1 PPB/G
LVCMOS/LVTTL compatible output
AEC-Q100 qualified
5-pin SOT23-5 package: 2.9 x 2.8 mm x mm
RoHS and REACH compliant, Pb-free, Halogen-free and
Antimony-free
Contact SiTime
for up-screening and LAT programs
Avionics systems
Field communication systems
Telemetry applications
Electrical Characteristics
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and nominal supply voltage.
Parameters
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
115.20
-20
-25
-30
-50
Operating Temperature
Range (ambient)
T_use
-40
-40
-40
-55
Acceleration (g) sensitivity,
Gamma Vector
Supply Voltage
Current Consumption
F_g
–
Typ.
–
–
–
–
–
–
–
–
–
–
Max.
137
+20
+25
+30
+50
+85
+105
+125
+125
0.1
Unit
MHz
ppm
ppm
ppm
ppm
°C
°C
°C
°C
ppb/g
AEC-Q100 Grade 3
AEC-Q100 Grade 2
AEC-Q100 Grade 1
Extended cold, AEC-Q100 Grade1
Low sensitivity grade; total gamma over 3 axes; 15 Hz to 2 kHz;
MIL-PRF-55310, computed per section 4.8.18.3.1
All voltages between 2.25V and 3.63V including 2.5V, 2.8V, 3.0V and
3.3V are supported.
Contact SiTime
for 1.5V support
No load condition, f = 125 MHz, Vdd = 2.25V to 3.63V
No load condition, f = 125 MHz, Vdd = 1.62V to 1.98V
Condition
Refer to Tables 14 to 16 for the exact
list of supported frequencies
Inclusive of Initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply voltage
and load (15 pF ± 10%).
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Rugged Characteristics
Supply Voltage and Current Consumption
Vdd
Idd
1.62
2.25
–
–
Duty Cycle
Rise/Fall Time
Output High Voltage
DC
Tr, Tf
VOH
45
–
–
90%
1.8
–
6
4.9
–
1.5
1.5
–
1.98
3.63
8
6
55
3
2.5
–
V
V
mA
mA
%
ns
ns
Vdd
Vdd = 2.25V - 3.63V, 20% - 80%
Vdd = 1.8V, 20% - 80%
IOH = -4 mA (Vdd = 3.0V or 3.3V)
IOH = -3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOH = -2 mA (Vdd = 1.8V)
IOL = 4 mA (Vdd = 3.0V or 3.3V)
IOL = 3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOL = 2 mA (Vdd = 1.8V)
Pin 1, OE
Pin 1, OE
Pin 1, OE logic high or logic low
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
Input Characteristics
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
–
–
100
–
30%
–
Vdd
Vdd
k
Rev. 0.5
July 22, 2019
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Table 1. Electrical Characteristics
(continued)
Parameters
Startup Time
Enable/Disable Time
Standby Current
Symbol
T_start
T_oe
I_std
Min.
–
–
–
–
Typ.
–
–
2.6
1.4
Max.
5.5
130
–
–
Unit
ms
ns
A
A
Jitter
RMS Period Jitter
RMS Phase Jitter (random)
T_jitt
T_phj
–
–
–
–
1.6
1.8
0.7
1.5
2.5
3
–
–
ps
ps
ps
ps
f = 125 MHz, 2.25V to 3.63V
f = 125 MHz, 1.8V
PRELIMINARY
Condition
Measured from the time Vdd reaches its rated minimum value
f = 115.20 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles
Vdd = 2.8V to 3.3V,
ST
= Low, Output is weakly pulled down
Vdd = 2.5V,
ST
= Low, Output is weakly pulled down
Startup and Resume Timing
f = 125 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
f = 125 MHz, Integration bandwidth = 12 kHz to 20 MHz
Table 2. Pin Description
Pin
1
2
Symbol
GND
NC
Power
No Connect
Output Enable
3
OE/NC
No Connect
4
5
VDD
OUT
Power
Output
Functionality
Electrical ground
[1]
No connect
H
[2]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
Any voltage between 0 and Vdd or Open
[2]
: Specified
frequency output. Pin 3 has no function.
Power supply voltage
[1]
Oscillator output
NC
2
Top View
GND
1
5
OUT
YXXXX
OE/NC
3
4
VDD
Figure 1. Pin Assignments
Notes:
1. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
2. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 3 is not externally driven. If pin 3 needs to be left floating, use the NC option.
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[3]
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Table 4. Thermal Consideration
[4]
Package
SOT23-5
Note:
4. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
JA, 4 Layer Board
(°C/W)
421
JC, Bottom
(°C/W)
175
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
85°C
105°C
125°C
Maximum Operating Junction Temperature
95°C
115°C
135°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Rev. 0.5
Page 2 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
PRELIMINARY
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 0.5
Page 3 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
Test Circuit and Waveform
Test
Point
Vout
Vdd
PRELIMINARY
tr
5
4
0.1µF
Power
Supply
tf
80% Vdd
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
15 pF
(including probe
and fixture
capacitance)
1
2
3
Vdd
1k
OE/ST Function
Figure 2. Test Circuit
[6]
Note:
6. SiT2045 has “no runt” pulses and “no glitch” output during startup or resume.
Figure 3. Waveform
[6]
Timing Diagrams
Vdd
90% Vdd
Vdd
50% Vdd
T_oe
No Glitch
during start up
Pin 4 Voltage
T_start
OE Voltage
CLK Output
HZ
CLK Output
HZ
T_start: Time to start from power-off
T_oe: Time to re-enable the clock output
Figure 4. Startup Timing (OE Mode)
[7]
Figure 5. OE Enable Timing (OE Mode Only)
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 6. OE Disable Timing (OE Mode Only)
Note:
7. SiT2045 has “no runt” pulses and “no glitch” output during startup or resume.
Rev. 0.5
Page 4 of 12
www.sitime.com
SiT2045B
115.2 – 137 MHz, -55 to 125°C, SOT23, Endura™ Series Oscillator
[size=4]A stack is a storage structure with a special access attribute of "Last In First Out" (LIFO). A stack generally uses RAM physical resources as a storage body, plus a LIFO access interface. [/s...
We can’t help but get excited about the evolution of transportation and the new technology that surrounds it. Innovative use cases around electric mobility(cars, motorcycles, electronic bicycles) and ...
1. The pulse capture module is used to capture the rising and falling edges of the pulse quantity, and then the pulse width and duty cycle are calculated.
2.6 groups of ecap modules can also be used a...
Since the establishment of this board, many netizens have posted many very valuable posts here. Xiaoguan took advantage of this epidemic to read the posts of this board in the past two years while sta...
For reference only
I am moving house recently and all the instruments and equipment have been packed, so there is no actual testing and debugging. This plan is for reference only.
I made this transcei...
I would like to ask how to automatically add test points to the whole board in AD? The current method is rather clumsy. For example, for 20 networks, I first copy 20 test point pads, then add networks...
In January this year, a federal jury in the United States ruled that Apple and Broadcom infringed California Institute of Technology's Wi-Fi data transmission-related patents, and the two companies w...[Details]
The Bitobar flowmeter is a flowmeter with only one sensor suitable for multiple media. It can be widely used in the measurement of gas, steam and liquid flow. The following are six features of the Bit...[Details]
It can be seen from formula GS0512 that in order to improve the common-mode rejection ratio of the differential amplifier circuit , the common-mode negative feedback resistance Re must be increa...[Details]
The EU will force all new cars to be equipped with DMS starting in July 2022. The EU's requirements are divided into two items, one is driver drowsiness and attention warning; the other is advanced d...[Details]
The coating thickness gauge is also called the coating thickness gauge. The principle and application are as follows:
1. Principle
Principle of magnetic thickness measurement: When the pr...[Details]
It can be transplanted into any digital clock program and the values of TH0 and TL0 can be modified according to the microcontroller model and crystal frequency. Intelligent date and time accumul...[Details]
With the continuous expansion of the application scope of laser marking machines, the speed and accuracy requirements for laser marking are also getting higher and higher. TI (Texas Instruments)'s TM...[Details]
To put it simply, timer counting converts the internal clock signal (fmaster) into an external clock signal (TIx, ETR). Counting requires a clock/trigger controller and a time base unit. Timer 1 has ...[Details]
0 Overview The "Computer Network" course is a professional course in computer and communications offered by university computer and related majors. This course is highly practical, and many teaching...[Details]
With the continuous expansion of the monitoring scope, the traditional wired monitoring alarm can no longer meet the needs of users. However, with the development of GSM network, the hardware imple...[Details]
Recently, we learned from Tesla officials that in order to achieve fully autonomous driving capabilities, Tesla not only released its self-developed autonomous driving chip some time ago, but also la...[Details]
On October 23, Samsung SDI announced that it had signed an electric vehicle battery supply contract with Hyundai Motor Company and will supply batteries to Hyundai Motor’s next-generation European b...[Details]
This is a project of our company. In the past, we used the virtual serial port based on USB to communicate with the upper and lower computers. Because USB is usually only used for updating parameters ...[Details]
RS232 serial port communication
- serial port USART0 communication experiment
I. Experimental purpose
Using the serial port debugging software, the data sent by AT91SAM7S64 can be correctly r...[Details]
Temperature sensors are instruments for measuring temperature and are widely used in industry, scientific research, medical treatment and other fields. This article will introduce in detail the mea...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
