3M
™
Molded-On Cable Assembly, 2 mm
The entire gas-tight
insulation displacement
contact area is encased in
insulation material
The cable end
is concealed
inside the
connector body
During the molding process, the
cable insulation is thermally fused
to the surrounding connector body
plastic to provide exceptional
strain relief
All cable assemblies use industry-standard
1 mm pitch round conductor flat ribbon cable
Sockets mate
with industry-
standard
2mm x 2mm
headers and plugs
For 3M Molded-On Assembly Cable Assemblies on
.100” x .100” spacing, see the following technical data sheets
on our website – www.3m.com/interconnects:
• .100” Molded-On Assembly, TS-2149
• .100” Molded-On DIP, TS-2152
• .100” Molded-On PCB, TS-2153
• .100” Molded-On Socket, TS-0632
For 3M Molded-On Cable Assemblies on 2 mm spacing,
reference:
• 2 mm Molded-On Assembly, TS-2150
• 2 mm Molded-On Socket, TS-0525
• 2 mm Molded-On PCB, TS-2151
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain
any of the substances in excess of the maximum concentration values in EU Directive
2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in
an application that is exempt under EU RoHS. This information represents 3M’s knowledge
and belief, which may be based in whole or in part on information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix,
then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty
stated below.
Note: A fan-out assembly, with multiple connectors on one end, requires a drawing submittal and review.
A
B
Length (Dim A) Tolerance
Note: A fan-out assembly, with multiple connectors on one end, requires a drawing submittal and review.
Min
Max
Tol
Available Options
± 0.3
Available Options
1.7
10.0
3M Molded-On Cable Assembly
™
Connector/Pos.
Socket
Cable
6
8
10
X
X
X
10
12
X
X
16
X
X
X
C
20
X
X
X
20
6
22
X
X
24
X
X
Connector/Pos.
X
X
X
A
X
X
X
PCB
2 mm x 2 mm
Cable / Pos.
Red Stripe
Conductor #1
(near side)
26
Socket
D
PCB
Cable
30
X
X
X
X
X
6
X
X
Left Connector
Right Connector
X
Cable / Pos.
26
X
6
30
22
8
10.0
10
34*
X
20.0
X
X
X
40.0
X
X
120.0
8
10
X
36
40.0
X
12
X
12
20.0
16
± 0.5
20
X
± 0.6
40
X
X
X
44
X
X
X
22
X
44
X
22
24
X
X
24
50
X
X
X
X
X
X
26
30
X
X
X
30
34*
X
36
X
40
X
X
X
40
44
X
X
X
44
50
X
X
X
50
X
X
X
120.0
±
X
1.0
X
X
X
16
± 2.0
X
34
X
36
20
26
* Check for availability in late 2007.
6
8
Note: If “Keying” is required, mark the circuit(s) to key.
Note: A fan-out assembly, with multiple connectors on one end, requires a drawing submittal and review.
1
Left Connector (Odd Row)
X
12
16
22
24
12
34
36
40
50
49
* Check for availability in late 2007.
A
2
Note: If “Keying”
Socket
is required, mark the circuit(s) to key.
X
X
X
X
X
X
B
Connector/Pos.
Min
Length (Dim A) Tolerance
Max
Available Options
8
1
C
D
Red Stripe
Conductor #1
(near side)
Right Connector
Left Connector
2
X
X
X
X
X
10.0
± 0.3
< Red Cable Stripe
PCB
X
X
Row)
X
X
X
X
X
X
49
X
X
Left Connector
20.0
(Odd
± 0.5
10.0
X
Cable
X
X
X
X
X
X
X
X
X
X
X
X
1
Right Connector (Odd Row)
20.0
40.0
± 0.6
34
Cable / Pos.
6
8
10
12
16
20
22
24
26
30
36
40
40.0
120.0
± 1.0
* Check for availability in late 2007.
120.0
± 2.0
Note: If “Keying” is required, mark the circuit(s) to key.
Tol
10
16
20
24
26
30
(Even Row)
(E
34*
36
40
44
X
X
X
44
50
X
X
X
50
50
1.7
49
1
(Even Row)
(E
2
Left Connector (Odd Row)
(Even Row)
50
49
50
Note: A fan-out assembly, with multiple connectors on one end, requires a drawing submittal and review.
< Red Cable Stripe
2
(Even Row)
(E
50
Connector/Pos.
Socket
PCB
Cable
Cable / Pos.
1
Available Options
6
X
X
X
6
8
X
X
X
8
10
X
X
X
10
12
X
X
12
16
X
X
X
16
20
X
X
X
20
< Red Cable Stripe
Right Connector (Odd Row)
22
X
X
24
26
X
X
X
30
X
X
X
34*
X
36
X
40
X
44
X
50
X
49
2M XX XX - XXX - XXXX - XXX.X - XX - XX - XX - X
49
Number of
Cable Conductors
Assembly
Length
Tip-to-Tip
inches
(Dim A in inches)
Example:
001.7 = 1.7” Min
Marking
0 = No Marking
1 = Label - Date Code
2 = Inkstamp - Date Code
Left Right
Centerbump Orientation
Options
0 = None
1 = Inside
2 = Outside
Connector Orientation
Options
(Left and Right)
AB = Up-Up
AD = Up-Down
CB = Down-Up
CD = Down-Down
1
X
Connector Types
(Left and Right)
Right Connector (Odd Row)
2
22
2
24
(Even
26 30
Row)
X
X
34
X
36
* Check for availability in late 2007.
Note: If “Keying” is required, mark the circuit(s) to key.
Socket, Low Profile
X
(.29” )
X
X
AA = no Centerbump, no Latching Ear
AB = Centerbump,
X
Latching Ear
no
X
X
AC = no Centerbump, with Latching Ear
40
= Centerbump, with
44
AD
(Even Row)
50
Latching Ear
PCB, 2-Row
BD = Matte Sn Plating, Straight Solder Tail
50
50
Ordering Information
2
< Red Cable Stripe
1
Left Connector (Odd Row)
49
Cable Product Series
28 AWG
3625 = Stranded, PVC
Connector Types
1
(Left and Right)
Socket, Low Profile
AA = no Centerbump, no Latching Ear
AB
2
= Centerbump, no Latching Ear
(Even Row)
AC = no Centerbump, with Latching Ear
AD = Centerbump, with Latching Ear
PCB, 2-Row
BD = Matte Sn Plating, Straight Solder Tail
Connector Types
(Left and Right)
Socket, Low Profile
(.29” )
AA = no Centerbump, no Latching Ear
AB = Centerbump, no Latching Ear
Right Connector (Odd Row)
no Centerbump, with Latching Ear
AC =
AD = Centerbump, with Latching Ear
PCB, 2-Row
(.29” )
BD = Matte
Number
Straight Solder Tail
Sn Plating,
of
(Even Row)
(E
Left
2M XX XX - XXX - XXXX - XXX.X - XX - XX - XX - X
Right
2M XX XX - XXX - XXXX - XXX.X - XX - XX - XX - X
Number of
Note: RIA E1 & C1 apply for all cables and connectors listed
Tip-to-Tip
Cable Conductors
inches
49
(Dim A in inches)
Assembly
Example:
Length
001.7 = 1.7” Min
50
Connector Feature Options
0 = No Keying Required
Assembly
Length
4 = Keying Required, specifiy position(s)
Cable Conductors
inches
50
28 AWG
Cable Product Series
3625
(Dim A in
PVC
= Stranded,
inches)
Tip-to-Tip
Left Right
0 = No Marking
Centerbump Orientation
Options
Label - Date Code
1=
0 =
2 = Inkstamp - Date Code
None
1 = Inside
2 = Outside
Marking
Marking
0 = No Marking
1 = Label - Date Code
2 = Inkstamp - Date Code
Example:
Left
001.7 = 1.7” Min
Right
Connector Feature Options
0 = No Keying Required
Cable
- XXX.X -
4
- XX - X
- XXXX
Product Series
XX - XX
= Keying Required, specifiy position(s)
Note:
28 AWG
apply for all cables and connectors listed
RIA E1 & C1
Marking
3625 =
Assembly
PVC
Stranded,
2M XX XX - XXX
Connector Types
(Left and Right)
Socket, Low Profile
(.29” )
AA = no Centerbump, no Latching Ear
AB = Centerbump, no Latching Ear
AC = no Centerbump, with Latching Ear
AD = Centerbump, with Latching Ear
PCB, 2-Row
BD = Matte Sn Plating, Straight Solder Tail
Left
Connector Orientation
Right
Options
Centerbump Orientation
(Left and Right)
Options
Up-Up
AB =
= Up-Down
0 =
AD = Down-Up
None
CB
1 =
CD = Down-Down
Inside
2 = Outside
Connector Orientation
Options
(Left and Right)
AB = Up-Up
AD = Up-Down
CB = Down-Up
CD = Down-Down
Number of
Cable Conductors
Connector
Options
0 = None
0 = No Keying Required
Cable Product Series
1 = Inside
4 = Keying Required, specifiy position(s)
= Outside
2
28 AWG
Left
Right
Connector Feature Options
0 = No Keying Required
4 = Keying Required, specifiy position(s)
Length
Tip-to-Tip
inches
Left
(Dim A in inches)
Right
Example:
001.7 = 1.7” Min
Feature Options
0 = No Marking
1 = Label - Date Code
2 = Inkstamp - Date Code
Left Right
Centerbump Orientation
3625 =
Note: RIA E1 & C1 apply for all cables and
Stranded, PVC
listed
connectors
3M is a trademark of 3M Company.
Connector Orientation
Options
(Left and Right)
AB = Up-Up
AD = Up-Down
CB = Down-Up
CD = Down-Down
Note: RIA E1 & C1 apply for all cables and connectors listed
Important Notice
PRODUCT USE:
All statements, technical information and recommendations
contained in this document are based upon tests or experience that 3M believes
are reliable. However, many factors beyond 3M’s control can affect the use and
performance of a 3M product in a particular application, including the conditions
under which the product is used and the time and environmental conditions in
which the product is expected to perform. Since these factors are uniquely within
the user’s knowledge and control, it is essential that the user evaluate the 3M
product to determine whether it is fit for a particular purpose and suitable for the
user’s application.
Warranty; Limited Remedy; Limited Liability.
3M’s product warranty is stated in its Product Literature available upon request.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
If this product is defective within the warranty period stated above,
your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product
or refund the purchase price of the 3M product.
Except where prohibited by
law, 3M will not be liable for any indirect, special, incidental or consequential
loss or damage arising from this 3M product, regardless of the legal theory
asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800 225 5373
www.3M.com/interconnects
Please recycle. Printed in USA.
© 3M 2007. All rights reserved.
80-4000-1955-2
NXP MCU
京公网安备 11010802033920号
EEWORLD
