EEWORLDEEWORLDEEWORLD

Part Number

Search

2200GG3F00923LB

Description
Strain Guage Sensor, Gage, -15Psi Min, 15Psi Max, 0.15%, 0.20-10.20V, Cylindrical
CategoryThe sensor    Sensor/transducer   
File Size507KB,4 Pages
ManufacturerGems Sensors & Controls
Download Datasheet Parametric View All

2200GG3F00923LB Overview

Strain Guage Sensor, Gage, -15Psi Min, 15Psi Max, 0.15%, 0.20-10.20V, Cylindrical

2200GG3F00923LB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codeunknow
Maximum accuracy(%)0.15%
shellSTAINLESS STEEL
Nominal offset0.20V
Maximum operating temperature80 °C
Minimum operating temperature-20 °C
Output range0.20-10.20V
Output typeANALOG VOLTAGE
Package Shape/FormCYLINDRICAL
port typeG1/8 FEMALE
Maximum pressure range15 Psi
Minimum pressure range-15 Psi
Pressure sensing modeGAGE
Sensor/Transducer TypePRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage35 V
Minimum supply voltage1.5 V
Termination typePLASTIC CABLE GLAND
Base Number Matches1
[Qinheng Trial] Experience of CH549 capacitive touch function
Happy weekend everyone! Today I experienced the serial port printing and capacitive touch button functions of the development board. When I applied for the development kit, I wanted to experience the ...
yin_wu_qing MCU
Raspberry Pi PICO low-resolution thermal imager
Using the Raspberry Pi PICO and CircuitPython system, plus the AMG8833 sensor and TFT screen, you can make a thermal imager.Project website :https://www.recantha.co.uk/blog/?p=20959...
dcexpert MicroPython Open Source section
Why does the power consumption of stm32L0 increase after it enters STOP mode again after being woken up by an external interrupt in STOP mode?
The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...
StruggleMySen stm32/stm8
[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
wangran_95 TI Technology Forum
Using registers to do STM8 UART1 error request help
[i=s]This post was last edited by zhang520 on 2021-10-21 15:08[/i]Error[Li006]: duplicate definitions for "_interrupt_21"; Change 21 to 20 and the system will run fine...
zhang520 stm32/stm8
BearPi-HM Nano Development Board Review 0 Unboxing and Development Environment Setup
[i=s]This post was last edited by symic on 2022-3-20 19:42[/i]I am very happy and surprised to get the opportunity to review the BearPi-HM Nano development board. Thanks to Nanjing BearPi Intelligent ...
symic Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号