IP Rating ............................................................ IP 40 .....................................................................IP 40
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Mechanical Characteristics
1
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing)...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers).............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE:
1
At
Performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Model 91 PC Pin Terminals, In-Line
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
Model 92 J-Hooked
Terminals, In-Line
.79
(.031) 2 PLCS.
3 2 1
.254
(.010)
GAP
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
10.16 ± 0.30
(.400 ± .012)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
15.29 ± 0.56
(.602 ± .022)
5.08
(.20)
1.52
(.06)
R2
R1
1
2
3
1
2
3
2.54
(.100)
2.54
(.100)
Model 94 J-Hooked
Terminals, "L" Pattern
0.76 ± 0.05
(.030 ± .002)
TYP.
Model 93 PC Pin Terminals, "L" Pattern
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
3 2 1
1.52
(.06)
GAP
.81
(.032)
R. MAX.
5.33 ± .76
(.21 ± .03)
3.81
(.150)
MAX. TYP.
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
DIA.
0.81
TYP.
(.032)
10.16 ± 0.30
(.400 ± .012)
R2
R1
5.08 ± 0.38
(.200 ± .015)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
12.7 ± 1.02
(.500 ± .040)
Shaft Flat Orientation
2.54
(.100)
2.54
(.100)
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
1
3
2
1
3
2
0.76 ± 0.05
(.030 ± .002)
TYP.
1
CCW
2
POTENTIOMETER
3
Model 95 Solder Lug Terminals, "Triangular" Pattern
1. Transmission protocol of Bluetooth wireless technology
The transport protocol is responsible for confirming the location between Bluetooth devices, as well as managing and establishing logical and ...
I configured LIS2MDL according to the magnet calibration example in "an5040-LSM6DSL: Always-On 3D Accelerometer and 3D Gyroscope.pdf" and tried to read three sets of data from the three registers OUT_...
1. When the stepper motor runs directly according to the voltage sine wave, there is no problem and the motor rotates very steadily. Use DSP. 2. Do not want to use communication to control the rotatio...
A digital electronic clock is a timing device that uses digital display of seconds, minutes, hours, and days. Compared with traditional mechanical clocks, it has the advantages of accurate timekeeping...
I was so happy when I saw this event. Why? There are two reasons:
First, I wanted to pick up the dusty boards.
Second, I have a lot of boards, so isn’t this just running into my trap? ? ? ?
I love buy...
[size=4]Q value of the filter[/size] [size=4] [/size] [size=4]Q value has little effect on the actual filtering effect, but Q value represents loss/input power. The higher the Q value, the greater the...
Ⅰ. Write in front SPI (Serial Perripheral Interface) is a serial peripheral communication interface that mainly realizes communication between devices (master and slave). In terms of hardware, it is ...[Details]
Probing techniques are critical to quality oscilloscope measurements, and probes are often the first link in the oscilloscope measurement chain. If the probe performance is inadequate, you will see d...[Details]
1 Introduction
HHCE (Home Health Care Engineering) is gradually entering people's lives as people pay more attention to health and telemedicine develops. It advocates the concept of "seeki...[Details]
Recently I debugged the serial port on the S5PV210 baseboard I made. Because it is troublesome to write a program to test a serial port. So, I directly transplanted a minicom to the development board...[Details]
1. Static digital tube display To light up the digital tube, you need to use the P0 port and the P2 port. The P0 port is responsible for displaying the number to be output, and the P2 port is respo...[Details]
Components and measuring range of anti-corrosion electromagnetic flowmeter:
Main components:
The anti-corrosion electromagnetic flowmeter consists of a sensor and a converter. The sensor is...[Details]
Fixed gas detectors are detectors that are used more frequently in industrial devices and production processes. They can be installed at specific detection points to detect specific gas leaks. Fixed d...[Details]
1A metronome is a device that provides a periodic ticking or beating sound, the function of which is to establish a proper tempo for any musical performance.
When used in this way, it pr...[Details]
In the detection of composite material characteristics, circuit electrical characteristics, human ECG detection, nuclear magnetic resonance, etc., it is necessary to accurately measure the surface v...[Details]
This solution uses the AT89C51 microcontroller as the core. The software part adopts C language modular design. It has the functions of displaying the year, month, day, hour, minute, second and tem...[Details]
Silicon carbide is a wide-bandgap semiconductor substrate that is ideal for high-temperature, high-power applications such as electric vehicles, but is extremely difficult to produce. With a limited ...[Details]
Driven by market demand for improved computing performance and more integrated functions, the application areas of 16-bit and 32-bit microcontrollers (MCUs) are expanding. Battery-powered devices...[Details]
1. Experiment of using single chip microcomputer to drive buzzer;
a) Description: The buzzer of the Lab51 MCU experiment board is connected to P1.5 of the MCU
b) Basic requirement: Control the bu...[Details]
Function of the circuit
Phase shift circuit is a circuit that makes the sine wave phase advance or lag. Phase shift circuit can also change SIN wave into COS wave. For 3-phase A...[Details]
Design of 8-channel parallel data acquisition PCI module
Data acquisition is one of the main functions of automatic test systems. In some application areas, such as ultrasound and medical elec...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
