XCTN26014700F datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> XCTN26014700F

XCTN26014700F: DescriptionRES NET,THIN FILM,1.47K OHMS,100WV,1% +/-TOL,-50,50PPM TC,0303 CASE; CategoryPassive components The resistor; File Size118KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

XCTN26014700F Overview

RES NET,THIN FILM,1.47K OHMS,100WV,1% +/-TOL,-50,50PPM TC,0303 CASE

XCTN26014700F Parametric

Parameter Name	Attribute value
package instruction	SMT, 0303
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Chip
Manufacturer's serial number	CTN
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	0.254 mm
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-STD-883
resistance	1470 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	CTN
size code	0303
Temperature Coefficient	-50,50 ppm/°C
Tolerance	1%
Operating Voltage	100 V

Preview

Download Datasheet

View All

CTN

Vishay Electro-Films

Nichrome Thin Film, Center Tapped Resistors

CHIP

RESISTORS

FEATURES

•

Wire bondable

Product may not

be to scale

•

Center tap feature

•

Chip size: 0.030 inches square

•

Resistance range total: 10

to 1 MΩ

•

Ratio tolerances to: 0.1 %

•

Resistor material: Nichrome

•

Oxidized silicon substrate for good power dissipation

The CTN series is a center tapped nichrome resistor chip

providing excellent stability at 250 mW power levels. The

CTN offers the designer flexibility in use as either a single

value resistor or as two resistors with a center tap feature.

The CTNs six bonding pads allows the user increased layout

flexibility.

The CTNs are manufactured using Vishay Electro-Films

(EFI) sophisticated thin film equipment and manufacturing

technology. The CTNs are 100 % electrically tested and

visually inspected to MIL-STD-883.

APPLICATIONS

The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and

tracking between two resistors is critical.

Recommended for Hermetic environment where die is not exposed to moisture.

For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.

Vishay EFI measures low-value resistors by the four wire Kelvin technique.

TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES

Tightest Standard Tolerance Available

0.5 %

0.1 %

± 10 ppm/°C

± 25 ppm/°C

± 50 ppm/°C

± 100 ppm/°C

PROCESS CODE

CLASS H*

203

202

200

201

*MIL-PRF-38534 inspection criteria

1 MΩ

CLASS K*

263

262

260

261

100

200

1 kΩ

STANDARD ELECTRICAL SPECIFICATIONS

PARAMETER

TCR Tracking Between Halves (R

)

Center Tap Ratio,

Tolerance

Noise, MIL-STD-202, Method 308, 100

- 250 kΩ

Stability, 1000 h, + 125 °C, 125 mW

Operating Temperature Range

Dielectric Voltage Breakdown

Insulation Resistance

Operating Voltage

DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)

* 20 ppm/°C for

< 20

www.vishay.com

For technical questions, contact: efi@vishay.com

Document Number: 61024

Revision: 12-Mar-08

± 2 ppm/°C *

1 ± 1 % standard

- 35 dB typ.

± 0.1 %

ΔR/R

- 55 °C to + 125 °C

200 V

min.

100 V max.

250 mW

Recommended Resources

AD574 and RS-232C interface circuit

Thyristor magnetizer circuit one b

toy phone circuit

Weighing signal secondary instrument circuit

Integrated regulated power supply with fixed negative output to protect the input from short-circuit when using large capacitive loads

Simple diagram of trickle charging method

How to configure the low-level driver of the HT16L21 LCD? It is based on IIC.: ...; 一百年后的自己 51mcu

Practical DSP28335 Programming Ideas: When developing DSP, you need to configure its underlying hardware and peripherals accordingly. Only after the configuration is completed can you activate its corresponding modules and then write and ...; 灞波儿奔 DSP and ARM Processors

Constant current source, constant voltage source, voltage drop after MOS is turned on: Constant current source, constant voltage source, voltage drop after MOS is turned on 1. This is a very classic constant current circuit. The load current is only controlled by the op amp's in-phase i...; QWE4562009 Circuit Observation Room

[April 23 | Suzhou] High-speed digital and optical communication test seminar invites you to meet: Conference Introduction With the vigorous development of the Internet industry, the data traffic generated by data centers has become an important part of communication network traffic. As an importan...; eric_wang Integrated technical exchanges

TMS320C6748_UART(3) - UART polling mode: UART polling mode is much simpler than interrupt mode. The UART initialization code is as follows: Copy code1 voidUARTInit(void)2 {3 // Configure UART1 parameters4 // Baud rate 115200 data bits 8 stop...; fish001 DSP and ARM Processors

Award-winning live broadcast: Application of TI millimeter-wave radar in cars is now open for registration~: Award-winning live broadcast: Application of TI millimeter-wave radar in cars is now open for registration~Click here to registerLive broadcast time May 26, 10:00-11:30amLive Topic TI millimeter wave ...; EEWORLD社区 TI Technology Forum

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components