EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1005H3882DBTF

Description
RESISTOR, THIN FILM, 0.25 W, 0.5 %, 50 ppm, 38800 ohm, SURFACE MOUNT, 1005, CHIP
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN1005H3882DBTF Overview

RESISTOR, THIN FILM, 0.25 W, 0.5 %, 50 ppm, 38800 ohm, SURFACE MOUNT, 1005, CHIP

PTN1005H3882DBTF Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
Objectid1696360770
package instructionSMT, 1005
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length2.667 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance38800 Ω
Resistor typeFIXED RESISTOR
size code1005
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage100 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
EEWORLD University Hall----What can be easily charged?
What can be easily charged? : https://training.eeworld.com.cn/course/5015...
wanglan123 Power technology
Share the steps of DSP development
1. Development environment CCS (CodeCo   mposerStudio) is a complete DSP integrated development environment developed by TI. Since TI's DSP is widely used, CCS has become one of the most widely used D...
fish001 DSP and ARM Processors
The long-awaited Digi-Key STM32F7508-DK and MAiX Bit unboxing notes
[i=s]This post was last edited by blacksword on 2022-8-5 22:58[/i]In the wind and rain It has been more than ten years since I met EEWorldIt is rare to have one decade in life, another decadeWhat’s ev...
blacksword DigiKey Technology Zone
It is customary to connect a 120Ω resistor between RS485 interface AB and CAN interface H and L. I only have 100Ω in stock. Can it be replaced?
It is customary to connect a 120Ω resistor between the RS485 interface AB and the CAN interface H and L. The warehouse only has 100Ω. Can 100Ω be used instead of 120Ω?...
oyhprince PCB Design
Solenoid valve test circuit board
Help: Test the solenoid valve. The specific situation is as follows: use a 15.5v starting voltage to power on, so that the solenoid valve closes for 1s, then the voltage drops to a 5v stable voltage, ...
若言啊 MCU
How to make a two-angle bidirectional LED and a normal LED light up alternately
I want to use the two-corner bidirectional light-emitting tubes and ordinary light-emitting diodes to light up alternately, turning on green light, bidirectional blue light, and bidirectional red ligh...
ywccyx Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号