85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na? ), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
●
When high-pressure shower cleaning is implemented, there is a possibility of exfoliation of the top electrodes caused by the water pressure stress so please avoid
the implementation.
●
If the implementation is unavoidable, then please evaluate the products beforehand.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
9/30/19
28
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
To achieve 10kHz PWM output at P2.0 port, which is also the common operating frequency of motor control in applications, it is necessary to understand each clock clearly in order to output accurate fr...
Raspberry Pi 4 IP address setting, source replacement, adding power button and heat dissipation.
1. Fixed IP address setting
After the Raspberry Pi is installed, it will automatically obtain an IP add...
ESD (electrostatic discharge) is one of the most serious failure mechanisms in CMOS circuits. In severe cases, it can cause the circuit to burn itself out. This paper discusses the necessity of ESD pr...
I want to design a circuit that can collect ±10V voltage input. The design idea is to convert the ±10V voltage into 0-20V DC, and then attenuate the 0-20V DC to 0-5V and input it to AD for conversion....
Headhunting position in [Shanghai] or [Changzhou] [/size] [size=14px]Job responsibilities: [/size][u][size=14px]Main work: Hardware development of brushless [/size][size=14px] motor controller [/size]...
The two NMOS tubes on the primary side of the push-pull boost circuit are broken down. I put the multimeter in the diode position and tested one of the power tubes. I put the red test lead on the D po...
How to learn MCU? What are the steps to learn MCU? MCU enthusiasts often ask us. We have roughly summarized that the process of learning MCU can basically be divided into four stages:
The first stage...[Details]
Abstract: This paper presents a method to implement Modbus communication protocol on Xinlinx Spartan-3E evaluation board. This method uses PC as the host computer and embeds Picoblaze soft core on ...[Details]
STM32F1xx official information: "STM32 Chinese Reference Manual V10" - Chapter 14 General Timer STM32 timer: STM32F103ZET6 has a total of 8 timers, which are: Advanced timers (TIM1, TIM8); genera...[Details]
Introduction: Use the T0 and T1 timing counter functions of the AT89S51 microcontroller to count the frequency of the input signal, and the counting frequency result is displayed through an 8-bit dyn...[Details]
V-cone flowmeter installation diagram V-cone flowmeter is mainly used for flow measurement of liquid, fixed and gas. The installation method of V-cone flowmeter is relatively simple compared with...[Details]
China Energy Storage Network News:
On November 22, State Grid Corporation of China officially issued the "Inter-provincial Electricity Spot Trading Rules (Trial)" (hereinafter referred to a...[Details]
When developing single-chip microcomputer programs, many people rely on emulators. Once they leave the emulator, they feel at a loss. In fact, for FLASH memory single-chip microcomputers, programs ca...[Details]
/* I heard about the digital tube curtain display when I first learned about digital tubes.
But at that time, because my foundation was not good enough, I didn't think of it for a while. Today,
I sa...[Details]
A real-time oscilloscope must be properly configured to make accurate jitter measurements. Here is a step-by-step process that can be applied to any brand of real-time oscilloscope to manually set up...[Details]
1 Introduction Currently, the A/D used for sampling in existing magnetometers is mostly 10-bit A/D, which results in low sampling accuracy, large measurement error, and poor anti-interference ability...[Details]
A paper published in Nature Communications on the 31st reported a machine learning model that can partially reproduce the collective knowledge accumulated by professional chemists in their work. This...[Details]
A tire blowout while driving at high speed is a very dangerous or even fatal accident. According to statistics, 46% of domestic highway traffic accidents are caused by tire failure, of which 70% ar...[Details]
1 Overview
The position detection method adopted by the position sensorless brushless DC motor controller is the back-EMF third harmonic detection method. There are two signals input to the cont...[Details]
Industrial controllers are core devices in modern industrial automation systems. Their core technologies mainly include the following aspects:
Hardware Technology
The hardware t...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
