EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

SP3-060-SH263/01-99

Description
Board Connector, 60 Contact(s), 3 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size291KB,1 Pages
ManufacturerE-tec Interconnect Ltd.
Environmental Compliance  
Download Datasheet Parametric View All

SP3-060-SH263/01-99 Overview

Board Connector, 60 Contact(s), 3 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

SP3-060-SH263/01-99 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerE-tec Interconnect Ltd.
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT
body width0.3 inch
subject depth0.709 inch
body length2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN
Contact completed and terminatedTin (Sn)
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialNYLON
JESD-609 codee3
Manufacturer's serial numberSP
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number3
Number of rows loaded3
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.11 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts60
MAXIM was finally acquired
According to ADI news (https://www.analog.com/en/about-adi/news-room/press-releases/2021/8-26-21-adi-completes-acquisition-of-maxim-integrated.html), ADI has completed the acquisition of Maxim Integra...
dcexpert Talking
AD9 won't work anymore
The rules do not allow short circuits. I don't know why the wire can be pulled even though it is smaller than the gap, resulting in a direct short circuit. The original setup either pushed the existin...
呜呼哀哉 Analog electronics
Share: Lightning strike experiment configuration, differential mode and common mode interference path analysis and design principles
Lightning strikes are a common physical phenomenon and the main source of voltage stress for power adapters. Improper protection can cause power damage or restart, thus affecting the normal operation ...
qwqwqw2088 Analogue and Mixed Signal
Xunwei-i.MX6 development board manual update-non-device tree uboot-modify default environment variables
This document mainly introduces how to modify the default boot parameters of non-device tree uboot. After the iTOP-iMX6 development board is burned, the default is the system parameters and screen par...
遥寄山川 ARM Technology
How to solve the signal fluctuation from the sensor?
The signal from the sensor is very weak, and the circuit behind it has been amplified and filtered. When the detection quantity remains unchanged, the amplified signal has certain fluctuations. Lookin...
sfcsdc Analog electronics
TMS320C6678 power-on configuration
1. What is the DSP power-on reset configuration? The DSP big-endian, little-endian, self-starting (boot) mode, PCIe mode, and network coprocessor clock selection need to be selected at power-on reset....
Jacktang DSP and ARM Processors

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号