EEWORLDEEWORLDEEWORLD

Part Number

Search

D-SUB-205A-15SBTDB101

Description
D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug
CategoryThe connector    The connector   
File Size124KB,1 Pages
ManufacturerPalPilot
Download Datasheet Parametric View All

D-SUB-205A-15SBTDB101 Overview

D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug

D-SUB-205A-15SBTDB101 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerPalPilot
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.492 inch
subject depth0.492 inch
body length1.543 inch
Body/casing typePLUG
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderFEMALE
Contact materialNOT SPECIFIED
contact modeSTAGGERED
Contact resistance15 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance3000000000 Ω
Insulator colorWHITE
insulator materialPOLYAMIDE
JESD-609 codee0
Manufacturer's serial number205
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1#4-40
Installation option 2RIVET
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceTIN
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts15
Newbie help, Altium copper does not connect after plating
The first one is a picture I got from somewhere else, and the second one is the copper coating I applied myself. It is not connected to the copper foil. How can I apply it like the first picture?...
Alex1 Analog electronics
D-Class AMP Load RL Headphone Connection Problem
Dear experts, please tell me a question about the connection of headphones to Class D amplifier load As shown in the pictureThis is the case where one end of the earphone is connected to the output an...
jkairup Analog electronics
Analog Electronics Course Test + Data Converter Introduction - DC Parameters
The course selection test for analog electronics can help you learn analog electronics well and consolidate your knowledge of analog electronics. It is a good learning platform. [url]https://bbs.eewor...
hjl742876110 TI Technology Forum
How to measure the inductor current in a switching power supply
[i=s]This post was last edited by qwqwqw2088 on 2020-2-22 08:24[/i]Switching power supplies often use inductors to temporarily store energy. When evaluating these power supplies, measuring the inducto...
qwqwqw2088 Analogue and Mixed Signal
[MM32 eMiniBoard Review] Using MM32-LINK under IAR
The eMiniBoard integrates the MM32-LINK emulator. Normally, after installing the corresponding support package, you can find the MM32-LINK option in the MDK project settings.However, unlike MDK, the c...
littleshrimp Domestic Chip Exchange
BQ76940 cannot be powered off
I'm using BQ76940 now. I disconnected the highest level and found that the chip still has power, and the 3.3 of the chip is still there, and the I2C communication is also normal. I would like to ask t...
tsc12345 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号