EEWORLDEEWORLDEEWORLD

Part Number

Search

OEH310AT

Description
Plastic Surface Mount / HCMOS/TTL Oscillator
File Size32KB,1 Pages
ManufacturerETC2
Download Datasheet View All

OEH310AT Overview

Plastic Surface Mount / HCMOS/TTL Oscillator

OEH, OEH3 Series
Plastic Surface Mount / HCMOS/TTL Oscillator
PART NUMBERING GUIDE
Package
OEH = 14 Pin Dip / 5.0Vdc / HCMOS-TTL
OEH3 = 14 Pin Dip / 3.3Vdc / HCMOS-TTL
C A L I B E R
Electronics Inc.
Environmental/Mechanical Specifications on page F5
OEH 100 48 A T - 30.000MHz
Pin One Connection
Blank = No Connect, T = Tri State Enable High
Output Symmetry
Blank = 40/60%, A = 45/55%
Inclusive Stability
100= +/-100ppm, 50= +/-50ppm, 30= +/-30ppm, 25= +/-25ppm,
20= +/-20ppm, 15= +/-15ppm, 10= ±10ppm
Operating Temperature Range
Blank = 0°C to 70°C, 27 = -20°C to 70°C, 48 = -40°C to 85°C
ELECTRICAL SPECIFICATIONS
Frequency Range
Operating Temperature Range
Storage Temperature Range
Supply Voltage
Input Current
250.000kHz to 24.000MHz
24.001MHz to 50.000MHz
50.001MHz to 66.667MHz
66.668MHz to 106.250MHz
Inclusive of Operating Temperature Range, Supply
Voltage and Load
w/TTL Load
w/HCMOS Load
w/TTL Load
w/HCMOS Load
0.4Vdc to 2.4Vdc w/TTL Load; 20% to 80% of
Waveform w/HCMOS Load </=66.667MHz.
0.4Vdc to 2.4Vdc w/TTL Load; 20% to 80% of
Waveform w/HCMOS Load >66.667MHz.
@1.4Vdc w/TTL Load; @50% w/HCMOS Load
@1.4Vdc w/TTL Load or w/HCMOS Load
@50% of Waveform w/LSTTL or HCMOS Load
>66.667MHz
250.000kHz to 24.000MHz
24.001MHz to 66.667MHz
66.668MHz to 150.000MHz
No Connection
V
IH
V
IL
Revision: 1995-B
250kHz to 106.250MHz
0°C to 70°C / -20°C to 70°C / -40°C to 85°C
-55°C to 125°C
5.0Vdc ±10%, 3.3Vdc ±10%
30mA Maximum
45mA Maximum
60mA Maximum
80mA Maximum
±100ppm, ±50ppm, ±30ppm, ±25ppm, ±20ppm,
±15ppm or ±10ppm
(20, 15, 10 = 0°C to 70°C Only)
2.4Vdc Minimum
Vdd –0.5Vdc Minimum
0.4Vdc Maximum
0.5Vdc Maximum
5nSeconds Maximum
3nSeconds Maximum
50 ±10% (Standard)
50±5% (Optional)
50±5% (Optional)
10TTL or 50pF HCMOS Load
10TTL or 15pF HCMOS Load
10LSTTL or 15pF HCMOS Load
Enables Output
+2.2Vdc Minimum to Enable Output
+0.8Vdc Maximum to Disable Output
±5ppm / year Maximum
10mSeconds Maximum
±100pSeconds Maximum
±25pSeconds Maximum
Frequency Tolerance / Stability
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise Time
Fall Time
Duty Cycle
Load Drive Capability
Pin 1 Tristate Input Voltage
Aging (@ 25°C)
Start Up Time
Absolute Clock Jitter
One Sigma Clock Jitter
MECHANICAL DIMENSIONS
4.7 MAX
7.620
±0.203
Marking Guide
Line 1: Blank or 3 - Frequency
Line 2: CEI YM
Blank
3
CEI
YM
= 5.0V
= 3.3V
= Caliber Electronics Inc.
= Date Code (Year / Month)
14.0
MAX
0.51
±0.203
5.08 ±0.20 14
8
0.25 MIN
1
7
9.8 MAX
Pin 1: No Connect or Tri-State
Pin 7: Case Ground
Pin 8: Output
Pin 14: Supply Voltage
TEL
949-366-8700
FAX
949-366-8707
WEB
http://www.caliberelectronics.com
Detailed explanation of CAN bus
CAN (Controller Area Network) is a serial communication network that can realize distributed real-time control. When you think of CAN, you have to think of the German company Bosch, because CAN was de...
可乐zzZ MCU
Free Application | Maxim High-Performance Analog Toolkit (78 Devices Included)
MAXIM's high-performance analog products support your next design The Basic Analog Toolkit contains a selection of Maxim's high-performance analog circuit modules. This carefully curated set of device...
EEWORLD社区 Analog electronics
[TI recommended course] #SimpleLink?Wi-Fi?CC3120 project introduction#
//training.eeworld.com.cn/TI/show/course/5000...
GuyGraphics TI Technology Forum
Can you paint three-layer boards?
I am a hardware novice and now I need to draw a board. I used to draw two-layer boards, but now I can't draw the board with two layers, so I want to draw a four-layer board. I seem to have heard that ...
chenbingjy PCB Design
AT32F421 Review
As a necessary peripheral on the chip, ADC has a very high usage rate. Although it is usually 10-bit or 12-bit, it is sufficient for use in less stringent situations. Arteli is no exception. It has a ...
eew_Violet Domestic Chip Exchange
AD20 schematic diagram and PCB Cross select layout have problems
I use two monitors and draw in cross select mode. When I operate the PCB, such as selecting a device to rotate or deleting a trace, the PCB does not perform the corresponding operation, but the corres...
sparkshen PCB Design

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号