EEWORLDEEWORLDEEWORLD

Part Number

Search

LTSHR-135-S-14-B-T

Description
Board Connector, 35 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Wire Wrap Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size175KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

LTSHR-135-S-14-B-T Overview

Board Connector, 35 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Wire Wrap Terminal, Black Insulator, Receptacle

LTSHR-135-S-14-B-T Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerMajor League Electronics
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresMATING PIN LENGTH=0.318 INCH
body width0.1 inch
subject depth0.16 inch
body length3.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN LEAD (200) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
JESD-609 codee0
Manufacturer's serial numberLTSHR
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness200u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.622 inch
Terminal pitch2.54 mm
Termination typeWIRE WRAP
Total number of contacts35
【GD32F350】4. TCP transmission between GD32 and SIM800 GSM module
1. AT+CGDCONT=1,"IP","CMNET"[/color][/align][align=left][color=#000000] [font=宋体]Define[/font][font=Calibri]PDP[/font][font=宋体]Mobile scenario[/color][/align][align=left][color=#000000]2. AT+CGATT=1[/...
常见泽1 GD32 MCU
[Repost]Why can't operational amplifiers be used as comparators?
[align=left][font=微软雅黑]A comparator is a device with two inputs, inverting and non-inverting, and an output that typically has an output voltage range between the rails of the supply rails. The same i...
赵玉田 Analog electronics
Using the Quartus II Timequest Timing Analyzer to Constrain and Analyze Designs
Using the Quartus II Timequest Timing Analyzer to Constrain and Analyze Designs...
雷北城 EE_FPGA Learning Park
NV2+GW1N+STM32 infrared thermal imaging data display
[i=s]This post was last edited by littleshrimp on 2022-1-10 12:20[/i]In order to display the thermal imaging data on STM32, the last plan was to use GW1N to convert the parallel data of DS90C124 into ...
littleshrimp Domestic Chip Exchange
Newbie's question: amplifier input filtering
Can the GND in the red circle in the figure below be replaced with VCM2V5? What is the difference between doing so and connecting it to GND?...
littleshrimp Analog electronics
[Repost] Hardware filter design, have you paid attention to these parameters?
[align=left][color=rgb(25, 25, 25)][font="]Filters, as the name implies, filter out some specific frequency domain "waves" in the signal. According to their functions, they can be divided into low-pas...
皇华Ameya360 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号