EEWORLDEEWORLDEEWORLD

Part Number

Search

BTB-27-01-T-S-235

Description
Board Connector, 27 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size292KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

BTB-27-01-T-S-235 Overview

Board Connector, 27 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BTB-27-01-T-S-235 Parametric

Parameter NameAttribute value
MakerSAMTEC
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPCB STACKING CONNECTOR
body width0.079 inch
subject depth0.135 inch
body length2.133 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberBTB
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts27
Wi-Fi 6 VS Wi-Fi 5
...
btty038 RF/Wirelessly
MSP430G2553 serial communication
1: First, let's talk about some things you need to pay attention to when using the G2553 serial port.(1): Hardware connection. The jumper cap should be changed to HW instead of SW. Note that you can s...
灞波儿奔 Microcontroller MCU
Using PC as a peripheral emulator for ESP32
Works by Taiwanese netizens: Use ESP32 to drive PC simulated peripherals through UART, I2C, SPI, etc. [b]Usage scenarios[/b] [list] [*]Use PC to drive peripheral devices with I2C/SPI/GPIO/UART interfa...
dcexpert MicroPython Open Source section
The op amp output noise contains the switching frequency of DCDC, but the power supply is actually very clean. How to improve it?
[i=s]This post was last edited by samyang13 on 2020-10-11 15:08[/i]Hello everyone, I recently tested the output of the PA78 amplifier, which is only used for DC amplification, but found that the rippl...
samyang13 Analog electronics
Wind power introduction
Wind power  Wind energy is usually referred to as the kinetic energy of air flow. Wind power generation is the conversion of the kinetic energy of air flow into electrical energy. Strong winds contain...
beh Industrial Control Electronics
AD Sampling Notes
[size=4]1: The reference voltage needs to be accurate enough. It is recommended to use an external high-precision reference voltage. [/size] [size=4]2: If the PGA is adjustable, the smaller the gain f...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号