EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

BTB-20-01-T-S-300

Description
Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size292KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

BTB-20-01-T-S-300 Overview

Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BTB-20-01-T-S-300 Parametric

Parameter NameAttribute value
MakerSAMTEC
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPCB STACKING CONNECTOR
body width0.079 inch
subject depth0.2 inch
body length1.58 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberBTB
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts20
Op amp differential attenuation circuit problem
I want to use an op amp to make a voltage attenuation circuit to measure 3~48V DC signals. Attached is a preliminary circuit diagram, but the power frequency interference problem cannot be solved duri...
jesseyuan Analog electronics
17 IP design based on Avalon bus
...
至芯科技FPGA大牛 FPGA/CPLD
[ESP32-Audio-Kit Audio Development Board Review] IR Infrared Remote Control LED Light
With the IR infrared receiving module as an accessory, the development board can remotely control the LED light. Its overall structure is shown in Figure 1. Figure 1 Overall composition The pin connec...
jinglixixi RF/Wirelessly
Dismantling and Renovation of Old LED Bulbs
An LED lamp at home is broken. This is a common 9W LED bulb. Since it cannot be used, I thought of disassembling it and analyzing it.It is easy to disassemble. Just squeeze the lampshade in front and ...
dcexpert DIY/Open Source Hardware
Emitter follower principle and typical circuit
[size=4][color=#000000][backcolor=white]Typical circuit of emitter follower:[/backcolor][/color][/size] [size=4][color=#000000][backcolor=white] [/backcolor][/color][/size] [size=4][color=#000000][bac...
Jacktang Analogue and Mixed Signal
DSP's various lords
...
灞波儿奔 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号