EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

SP1-022-S120/02-66/2

Description
Board Connector, 22 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size349KB,2 Pages
ManufacturerE-tec Interconnect Ltd.
Environmental Compliance
Download Datasheet Parametric View All

SP1-022-S120/02-66/2 Overview

Board Connector, 22 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

SP1-022-S120/02-66/2 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerE-tec Interconnect Ltd.
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresROHS COMPLIANT
body width0.079 inch
subject depth0.236 inch
body length1.732 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10)
Contact completed and terminatedGold (Au)
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialPOLYBUTYLENE TEREPHTHALATE
JESD-609 codee4
Manufacturer's serial numberSP
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.098 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts22
Development of C-band Programmable Phase Shifter
Programmable phase shifters are widely used in microwave systems, especially in missile simulation systems. Their accuracy and delay are directly related to the simulation results of the entire missil...
JasonYoo Analog electronics
[GD32L233C-START Review] 8. Comprehensive Application of Kitchen Countdown Timer
[i=s]This post was last edited by lising on 2022-4-11 10:21[/i]This comprehensive experiment uses the GD32L233C-START development board to make a kitchen countdown timer with a timing range of 1 (min)...
lising GD32 MCU
Has anyone successfully mounted a USB flash drive with GD32+FATFS? Please advise
The current STM32105+FATFS 0.13C can be mounted on a USB flash drive normally.The code remains unchanged, only the STM32 on the board is replaced with GD32F105, and the USB flash drive cannot be mount...
mini_peng GD32 MCU
【i.MX6ULL】Driver Development 1——Character Device Development Template
The previous articles (starting from i.MX6ULL Embedded Linux Development 1-Preliminary Exploration of Uboot Transplantation ) introduced the system transplantation of embedded Linux (Uboot, kernel and...
DDZZ669 ARM Technology
What are the components FB1 and FB2 on the lpc824 DIP development board?
Recently I took a look at the information of the lpc824 DIP development board and found that there are two components FB1 and FB2 on the board, which are used to connect AGND and DGND. The schematic s...
bigbat NXP MCU
Can signaltap be set to automatically trigger after power-on? I encounter abnormal counting after power-on.
The debug script reads out that a register is 1 after power-on. This section of code is generated by a for loop. The initial values of the other registers are normal and there is no problem with the t...
qan FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号