VJ0805Q181JXAMC datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> VJ0805Q181JXAMC

VJ0805Q181JXAMC: DescriptionCAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.00018uF, SURFACE MOUNT, 0805, CHIP, ROHS COMPLIANT; CategoryPassive components capacitor; File Size178KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

VJ0805Q181JXAMC Overview

CAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.00018uF, SURFACE MOUNT, 0805, CHIP, ROHS COMPLIANT

VJ0805Q181JXAMC Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Vishay
package instruction	, 0805
Reach Compliance Code	compli
ECCN code	EAR99
capacitance	0.00018 µF
Capacitor type	CERAMIC CAPACITOR
dielectric materials	CERAMIC
JESD-609 code	e3
Manufacturer's serial number	VJ
Installation features	SURFACE MOUNT
multi-layer	Yes
negative tolerance	5%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	RECTANGULAR PACKAGE
method of packing	TR, PAPER, 7 INCH
positive tolerance	5%
Rated (DC) voltage (URdc)	50 V
size code	0805
surface mount	YES
Temperature characteristic code	C0G
Temperature Coefficient	-/+30ppm/Cel ppm/°C
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrie
Terminal shape	WRAPAROUND

Preview

Download Datasheet

View All

VJ High Q Dielectric

Vishay Vitramon

Multilayer Ceramic Chip Capacitors

FEATURES

•

COG is an ultra-stable dielectric offering a

Temperature Coefficient of Capacitance (TCC) of

0 ± 30 ppm/ °C over the entire temperature range.

•

Low Dissipation Factor (DF).

•

Ideal for critical timing and tuning applications.

RoHS

COMPLIANT

GENERAL SPECIFICATIONS

NOTE:

Electrical characteristics at + 25 °C unless otherwise

specified.

Capacitance Range:

1.0 pF to 680 pF.

Temperature Coefficient of Capacitance (TCC):

0 ± 30 ppm/ °C from - 55 °C to + 125 °C.

Dissipation Factor (DF):

0.1 % maximum at 1.0 Vrms and 1kHz for values >1000 pF.

0.1 % maximum at 1.0 Vrms and 1MHz for values

≤1000

pF.

Insulation Resistance (IR):

At + 25 °C and rated voltage 100,000 MΩ minimum or

1000

ΩF,

whichever is less.

At + 125 °C and rated voltage 10,000 MΩ minimum or

100

ΩF,

whichever is less.

Dielectric Withstanding Voltage (DWV):

This is the maximum voltage the capacitors are tested for

a 1 to 5 second period and the charge/discharge current does

not exceed 50mA

≤

200V DC : DWV at 250 % of rated voltage.

ORDERING INFORMATION

VJ0805

CASE

CODE

DIELECTRIC

101

CAPACITANCE

NOMINAL CODE

CAPACITANCE

TOLERANCE

TERMINATION

DC VOLTAGE

RATING

MARKING

PACKAGING

###

PROCESS

CODE

0805

1206

1210

Q = High Q

Expressed in

picofarads (pF).

The first two

digits are

significant, the

third is a

multiplier. An ‘R’

indicates a

decimal point.

Examples:

101 = 100 pF

1R8 = 1.8 pF

C = ± 0.25 pF

D = ± 0.5 pF

F=±1%

G=±2%

J=±5%

K = ± 10 %

NOTE:

C, D < 10 pF

F, G, J, K

≥

10 pF

X = Ni barrier

100% tin plated.

A = 50V

B = 100V

C = 200V

A = Unmarked

M = Marked

T = 7” reel / plastic tape

C = 7” reel / paper tape

R = 11 1/4” reel / plastic tape

P = 11 1/4” reel / paper tape

Note

1. DC voltage rating should not be exceeded in application

3. Process Code may be added with up to three digits, used to control non-standard products and/or special requirements

Document Number 45050

Revision: 22-Feb-05

www.vishay.com

Recommended Resources

transistor long delay circuit

Phase locked loop broadcast band receiver.gif

Self-stopping hypnotic circuit

555 zero volt switching circuit

KA2309 (toy) radio remote control receiving control and regulating circuit

820e computer motherboard circuit diagram_23

I used a better board, but I didn’t expect DDR4 to be…???: Author: Sun Yiwen, member of Yibo Technology Expressway self-mediaToday's wind is very noisy, and there are a lot of cars on Shennan Avenue. In a building in the Science and Technology Park, after sol...; yvonneGan PCB Design

Aren't all charging stations AC-DC, used to charge electric vehicles? Why are there DC charging stations?: Aren't all charging piles AC-DC, and then charge electric vehicles? Why are there DC charging piles? -----------A DC charging pile is a charging pile where the battery pack charges the battery pack of...; QWE4562009 Integrated technical exchanges

Solution to the problem that IAR compiles very slowly and prompts NO Valid when compiling the first file: [size=4]Share this with everyone... [/size] [size=4] [/size] [size=4] When you install IAR For ARM, you may encounter the following situation: everything from entering the registration code to install...; Jacktang Microcontroller MCU

[STM32WB55 Review] BLE_p2pServer Project Extraction & Compilation: CubeWB provides a lot of examples that can be used directly in the software development environment. It supports three IDEs - IAR EWARM, MDK-ARM and SW4STM32. The latter uses the GCC compiler. I don't...; cruelfox RF/Wirelessly

ST's latest sensor driver: It is really difficult to use GitHub after it was acquired. Previously, the sensor drivers in STMems StandardC drivers were in one project, and they could be directly packaged and downloaded on the In...; littleshrimp MEMS sensors

Why does the electromagnetic flow meter have a lining?: As for why electromagnetic flowmeters need linings, we should start with the principle of electromagnetic flowmeters. Electromagnetic flowmeters generally have a set of coils and two electrodes. The f...; cfybhd Sensor

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components