The ASDX Series is a Silicon Pressure Sensor offering a
ratiometric analog output for reading pressure over the
specified full scale pressure span and temperature range.
The ASDX is fully calibrated and temperature compensated for
sensor offset, sensitivity, temperature effects and non-linearity
using an on-board Application Specific Integrated Circuit
(ASIC). Calibrated output values for pressure are updated at
approximately 1 kHz.
The standard ASDX is calibrated over the temperature range
of 0 °C to 85 °C [32 °F to 185 °F]. The sensor is characterized
for operation from a single power supply of either 3.3 Vdc or
5.0 Vdc.
FEATURES
•
•
Ratiometric 12-bit analog output
Precision ASIC conditioning and temperature
compensated over 0 °C to 85 °C [32 °F to 185 °F]
temperature range
•
•
•
•
•
•
Low operating voltage
Absolute, differential and gage types
Pressure ranges from 10 inches H
2
0 to 100 psi
Standard calibrations in inches H
2
0, cm H
2
0, psi, mbar,
bar, kPa
Total error band of ±2.0% of full scale span maximum
RoHS compliant
•
•
•
•
•
•
•
These sensors are available to measure absolute, differential
and gage pressures. The absolute versions have an internal
vacuum reference and an output value proportional to absolute
pressure. Differential versions allow application of pressure to
either side of the sensing diaphragm. Gage versions are
referenced to atmospheric pressure and provide an output
proportional to pressure variations from atmosphere.
The ASDX Series sensors are intended for use with non-
corrosive, non-ionic working fluids such as air and dry gases.
They are designed and manufactured according to standards
in ISO 9001.
POTENTIAL APPLICATIONS
Flow calibrators
Ventilation and air flow monitors
Gas flow instrumentation
Sleep apnea monitoring and therapy equipment
Barometry
Pneumatic controls
HVAC
ASDX Series Silicon Pressure Sensors
Table 1. Absolute Maximum Ratings
Parameter
Supply voltage (V
supply
)
Voltage to any pin
ESD susceptibility (human body model)
Storage temperature
Lead temperature (2 s to 4 s)
2
External capacitance between V
supply
and ground
Table 2. Operating Specifications
Parameter
3
Supply voltage (V
supply
)
3.3 Vdc
5.0 Vdc
Sensors are either 3.3.Vdc or 5.0.Vdc based on models chosen per the
order guide (see Figure 1).
1
Min.
-0.3
-0.3
3
-50 [-58]
-
100
Max.
6.0
V
supply
+ 0.3
-
125 [257]
250 [482]
470
Unit
Vdc
Vdc
kV
°C [°F]
°C [°F]
nF
Min.
3.0
4.75
1.5
0 [32]
-20 [-4]
Typ.
3.3
4
5.0
4
Max.
3.6
5.25
Unit
Vdc
mA
°C [°F]
°C [°F]
Supply current
5
Compensated temperature range
6
Operating temperature range
7
Overpressure
8
Burst pressure
Startup time (power up to data ready)
Response time
Upper output clipping limit
Lower output clipping limit
Minimum load resistance
9
Total error band
Output resolution
Table 3. Environmental Specifications
Parameter
Humidity
Vibration
Shock
Life
Table 4. Wetted Materials
Parameter
Covers
Adhesives
Electronic components
11
-
-
97.5
-
5.0
-
12
2.5
3.5
-
85 [185]
-
105 [221]
2X operating pressure range minimum
3X operating pressure range minimum
-
5
1.0
-
-
-
-
2.5
-
-
-
2.0
-
-
ms
ms
% V
supply
% V
supply
kOhm
10
%FSS
bits
Characteristic
0% to 95% RH non-condensing
10 G at 20 Hz to 2000 Hz
100 G for 11 ms
1 million cycles minimum
Port 1 (Pressure Port)
glass-filled PBT
silicone
silicon and glass
12
Port 2 (Reference Port)
glass-filled PBT
silicone and epoxy
silicon, glass, and gold
12
Notes:
1.
Absolute maximum ratings are the extreme limits that the device will withstand without damage to the device.
2.
An external bypass capacitor is
required
across the supply voltage (Pins 1 and 3 – see Figure 4) as close to the sensor supply pin as possible for correct sensor
operation.
3.
Ratiometricity of the sensor (the ability of the output to scale to the input voltage) is achieved within the specified operating voltage for each option. Other custom
supply voltages are available, please contact Honeywell Customer Service.
4.
The sensor is not reverse polarity protected. Incorrect application of excitation voltage or ground to the wrong pin may cause electrical failure.
5.
The compensated temperature range is the temperature range (or ranges) over which the sensor will produce an output proportional to pressure within the
specified performance limits.
6.
The operating temperature range is the temperature range over which the sensor will produce an output proportional to pressure but may not remain within the
specified performance limits.
7.
Overpressure is the maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the operating
pressure range. Exposure to higher pressures may cause permanent damage to the product.
8.
Burst pressure is the maximum pressure that may be applied to any port of the product without causing escape of pressure media. Product should not be expected
to function after exposure to any pressure beyond the burst pressure.
9.
Total error band is the maximum deviation in output from ideal transfer function over the entire compensated temperature and pressure range. Includes all errors
due to offset, full scale span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span and thermal hysteresis.
Specification units are in percent of full scale span (%FSS).
10. Full scale span (FSS) is the algebraic difference between the output signal measured at the maximum (Pmax.) and minimum (Pmin.) limits of the pressure range.
11. Consult Honeywell Customer Service for detailed material information.
12. For the AC pressure port configuration, the “pressure” and “reference” ports are reversed.
2
www.honeywell.com/sensing
Low Pressure and Ultra-Low Pressure Analog Output
Figure 1. Nomenclature and Order Guide
Notes:
13. Other package combinations are possible, please contact Honeywell Customer Service.
14. The transfer function limits define the output of the sensor at a given pressure input. By specifying the output signal at the maximum (Pmax.)
and minimum (Pmin.) limits of the pressure range, the complete transfer curve for the sensor is defined. See Figure 2 for a graphical
representation of each calibration.
15. For a digital output, please refer to the ASDX Digital Series.
There is a board, STM32F407VET6, serial port 4 is connected to PC10 and PC11.I wrote a program using the standard library, but it can't communicate.
The initialization code is as follows://IO 4
//boun...
Now recruiting part-time dsp lecturers.
Short-term training can be done on weekends. If you want to earn some extra money, accumulate resources, and enrich your life, please contact me.Require:
① More...
Enter SILICON LABS official website:
https://cn.silabs.com/development-tools/mcu/32-bit/efm32pg22-development-kit Then select "Get Started"on the web pageand download and installSimplicity Studio vers...
The C6678.cmd file is grayed out for some reason. I didn't notice it at first, but when I compiled the project, I found that all memory allocated in DDR failed. Is it possible that my cmd file is not ...
[align=left] [color=#3d3d3d][font="][size=10.5pt]Click here to download the handouts for this seminar: [/size][/font][/color][/align][align=left][b]https://ez.analog.com/cn/webcasts/f/forum/109744/thr...
1. Introduction
As personal communication technology has been developing and maturing over the past 20 years, people have become increasingly dependent on wireless communication in their lives. Cur...[Details]
First, let’s talk about what port multiplexing is. STM32 has many built-in peripherals, and the external pins of these peripherals are multiplexed with GPIO. In other words, if a GPIO can be multiple...[Details]
LeCroy's signal integrity network analyzer SPARQ can quickly locate the crosstalk of connectors, backplanes and cables, and can use single-ended or differential port assignments to measure near-end c...[Details]
I believe everyone knows about RS485 communication. When learning about RS232, we will compare it with 485 (RS485 will be replaced by 485 below). Without talking about the advantages and disadvantage...[Details]
Method of repairing LCD color TV with oscilloscope Determine the fault scope based on the fault characteristics of the waveform In a faulty LCD TV, the waveform changes vary greatly, but there ar...[Details]
(1) Typical characteristics of poor contact. The poor contact phenomenon of pointer multimeters mostly occurs between the plug and the socket of the test line. The typical characteristics of the fau...[Details]
Today, well-known foreign whistleblowers Onleaks and foreign media Zoutons brought us the appearance renderings of Sony's new generation entry-level mobile phone Xperia 10 IV. This is also the ...[Details]
With the continuous changes in market demand, traditional telephones have gradually exposed problems such as single functions and inconvenient dialing. Aiming at the requirements of the dispatching...[Details]
The industry's pursuit of resolution has reached an obsession. We want every display to be high-resolution, no matter how big or small. But at the same time, we also want to make the devic...[Details]
Dry Cell Dry cell is a chemical battery that generates direct current with a paste electrolyte. It is roughly divided into primary cell and secondary cell. It is the most commonly used and lightweigh...[Details]
1 Introduction
Inductive key technology is an emerging technology that has been widely used in various products. Especially in the past two years, home appliances using inductive keys have been...[Details]
In early June, Shanghai announced the lifting of the lockdown. After two months of lockdown and anti-epidemic efforts, there is finally light at the end of the tunnel. Looking back at this round of d...[Details]
I also made this myself during the summer electronic design competition training, and the running results are pretty good. The pins are crossed because the P2 port is used. When designing the hardw...[Details]
Translated from - semiengineering The large-scale application of sensors and the development of machine learning have made centralized testing possible in some areas with greater impact. Machine ...[Details]
Introduction As a non-polluting energy source, the research on the utilization of solar energy has always been a hot topic. In order to improve the efficiency of solar energy conversion, the researc...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
