EEWORLDEEWORLDEEWORLD

Part Number

Search

GUS-QS8B-02-2492-F

Description
Array/Network Resistor, Bussed, 0.75W, 24900ohm, 100V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1519, QSOP-16
CategoryPassive components    The resistor   
File Size365KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUS-QS8B-02-2492-F Overview

Array/Network Resistor, Bussed, 0.75W, 24900ohm, 100V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1519, QSOP-16

GUS-QS8B-02-2492-F Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerTT Electronics plc
package instructionSMT, 1519
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresPRECISION
structureMiniature
Component power consumption0.05 W
The first element resistor24900 Ω
JESD-609 codee0
Manufacturer's serial numberQSOP
Installation featuresSURFACE MOUNT
Network TypeBUSSED
Number of components15
Number of functions1
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height1.626 mm
Package length4.902 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width3.912 mm
method of packingTR; TUBE
Rated power dissipation(P)0.75 W
Rated temperature70 °C
resistance24900 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesQSOP
size code1519
surface mountYES
Temperature Coefficient50 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeGULL WING
Tolerance1%
Operating Voltage100 V
Surface Mount QSOP
Resistor Networks
QSOP Series
Reliable, no internal cavity
High resistor density - .025" lead spacing
Standard JEDEC 16, 20, and 24 pin packages
Ultra-stable TaNSil
®
resistors on silicon substrate
RoHS compliant and Sn/Pb terminations available
IRC’s TaNSil
®
QSOP resistor networks are the perfect solution for high volume applications that demand a
small wiring board footprint. The 0.025" lead spacing provides higher lead density, increased component
count, lower resistor cost, and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking, low cost
and miniature package. Excellent performance in harsh, humid environments is a trademark of IRC’s
self-passivating TaNSil
®
resistor film.
The QSOP series is ideally suited for the latest surface mount assembly techniques and each lead can be
100% visually inspected. The compliant gull wing leads relieve thermal expansion and contraction stresses
created by soldering and temperature excursions.
For applications requiring high performance resistor networks in a low cost, surface mount package, specify
IRC QSOP resistor networks.
Electrical Data
Resistance Range
Absolute Tolerance
Ratio Tolerance to R1
Absolute TCR
Tracking TCR
Element Power Rating @ 70°C
Isolated Schematic
Bussed Schematic
Package Power Rating @ 70°C
Rated Operating Voltage
______
(not to exceed
P x R)
Operating Temperature
Noise
100mW
50mW
16-Pin
20-Pin
24-Pin
750mW
1.0W
1.0W
10 to 250KΩ
To ±0.1%
To ±0.05%
To ±25ppm/°C
To ±5ppm/°C
Environmental Data
Test Per
MIL-PRF-83401
Typical
Delta R
Max Delta
R
Thermal Shock
±0.02%
±0.1%
Power Conditioning
±0.03%
±0.1%
High Temperature Exposure
±0.03%
±0.05%
Short-time Overload
±0.02%
±0.05%
100 Volts
-55°C to
+125°C
<-30dB
Low Temperature Storage
±0.03%
±0.05%
Life
±0.05%
±2.0%
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
QSOP Series Issue January 2009 Sheet 1 of 4
Conversion of wire harness diameter between American standard AWG and national standard "square"
Recently, I have a task at work that requires calculating the wire diameter of the wire harness and corresponding to the US standard AWG wire number. I would like to share the conversion method and us...
Arvinˇ Analog electronics
RT-Thread System - Create a new project in Studio mode
For specific installation and use, please refer to the official website RT-Thread Studio Quick Reading Getting Started section Here is a little bit to say that after RT-Thread Studio is installed, you...
ID.LODA Embedded System
dxp2004 related issues
I see other people's interfaces are like thisbut I can't display so many in the sidebar, I can only select and then display them separately.and thishow can I make it display the same as theirs....
哈喽哈哈 PCB Design
When the frequency is too high, are there any special considerations for the low impedance requirements of the GND Via?
Is the relative frequency of the signal bypass arrangement above too high?What indicators does the specific parameter definition of via depend on?Impedance, heat dissipation, reflux, etc.................
btty038 RF/Wirelessly
USB3.0: LAYOUT Guide for VL817Q7-C0
This article focuses on the layout processing and precautions of the common USB3.0 hub driver chip VIA VL817-Q7C0 on the market. It can be divided into three sections. This article focuses on the firs...
禾川芯 PCB Design
TMS320C6678 Development Routine User Manual Study 5
3.4.2 Hardware Test (Disable Cache and Use Cache) Modify the code in the main.c file to select the hardware test mode, as shown in the following figure: After recompiling, use the emulator to connect ...
火辣西米秀 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号