The L-type/D-type/S-type/F-type/N-type Medallion 6000 Series
This product line is a family of state-of-the-art high performance 1550 nm
externally modulated CATV fiber optic transmitters optimized for varying network
applications. Packaged in convenient 1RU housing, this line of optical transmitters
couples high optical output powers, up to 11.0 dBm, with low optical line width
resulting in unmatched performance. The optical modulator, combined with
proprietary pre-distortion circuitry, provides superior CTB and CSO performance
with SBS suppression levels of greater than 21 dBm. Advanced features such as
built in field adjustable SBS control and electronic dispersion compensation allow
these transmitters to be quickly optimized in the field for any link or application
without the need to procure specifically tuned transmitters. This affords the system
designer a level of flexibility previously unknown in the CATV market place.
The L-type series are designed as a high performance solution for applications
where the simultaneous transport of CATV and SAT-IF FM signals is required.
The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band.
The D-type series are designed as a low cost, high performance solution for
applications where the required fiber length is in the range of 20 to 50 kilometers.
Advanced, high power, DFB laser technology allows these transmitters to be
fielded without the use of EDFAs.
The S-type series transmitters are designed to be the most versatile model within
the Medallion 6000 series family. They can easily be configured to meet most
HFC network solutions requiring link lengths in the range of 50 to 70 kilometers
with one EDFA as well as links utilizing multiple EDFA’s.
The H-type series transmitters are optimized for single EDFA fiber links in the 70
to 90 kilometer range. These transmitters take advantage of our advanced fiber
dispersion compensation circuitry to provide exceptional CATV performance.
The F-type series transmitters are intended for use in FTTx and RFoG
architecture designs requiring high quality transmission over varying transmission
lengths and EDFA output powers. These transmitters successfully support very
high optical launch powers while controlling the detrimental effects of Stimulated
Brillouin Scattering (SBS), group velocity dispersion (GVD), and self phase
modulation (SPM).
The N-type series transmitters are intended for use in node-splitting architecture
designs requiring cost effective DWDM transmission over medium length fiber
distances.
Applications
High Performance Supertrunking Links
High Power Distribution Networks
Redundant Ring Architectures
FTTx Networks
RFOG Applications
SAT-IF Transport
DWDM Node Splitting
Features
Single or Dual Optical Outputs
QAM Loading to 1003 MHz
Dual Power Supplies, Redundant &
Hot Swappable
Front Panel RF Test Point
SNMP Control Interface
WEB GUI
Vacuum Fluorescent Status Display
OMI / RF Gain Adjustment
AGC Select: CW, Video, Manual
(No AGC)
Industry Leading Field Adjustable
SBS Suppression
Field Adjustable Electronic
Dispersion Compensation (EDC)
| REV 2011.12
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 6000 Series 1550 nm
Externally Modulated Transmitter
DATASHEET | DECEMBER 2011
FIBER OPTICS
Optical / Electrical Characteristics
L-type
Property
Performance (Note 1-8)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
CATV Carrier to Noise Ratio
CATV Composite Second Order
CATV Composite Triple Beat
CATV Composite Triple Beat
SAT-IF Carrier to Noise Ratio
SAT-IF Intermodulation Products
SAT-IF Spurious Products
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
CNR (dB)
(dBc)
(dBc)
Units
6000-L01
L (km)
25
NTSC 80-Ch
8.5/8.5
4
15.0
51.0
-65
-65
-64
27
-35
-38
Models
6000-L02
6000-L03
25
PAL 60-Ch
8.5/8.5
5
15.0
51.0
-65
-65
-64
27
-35
-38
25
NTSC 110-ch
8.5/8.5
4
15.0
49.5
-65
-65
-64
27
-35
-38
Comments
6000-L04
25
PAL 89-Ch
8.5/8.5
5
15.0
49.5
-65
-65
-64
27
-35
-38
Min.
Min.
Max. Port 1
Max. @ +25C
Max. @ 0 C to 50 C
Min.
Max. Port 1
Max.
o
o
With 36 QPSK carriers
from 950 to 2800 MHz
Min. 10 dBm version
avail. See Chart
D-type
Property
Performance (Note 1-7)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
Carrier to Noise Ratio
Composite Second Order
Composite Triple Beat
Composite Triple Beat
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
Units
6000-D01
L (km)
40
NTSC 80-Ch
11.0
4
> 12.0
54.0
-65
-65
-64
Models
6000-D02
6000-D03
40
PAL 60-Ch
11.0
5
>12.0
54.0
-65
-65
-64
40
NTSC 110-ch
11.0
4
>12.0
51.0
-65
-65
-64
Comments
6000-D04
40
PAL 89-Ch
11.0
5
>12.0
51.0
-65
-65
-64
Min.
Min.
Max.
Max. @ +25C
Max. @ 0 C to 50 C
o
o
Min.
S-type
Property
Performance (Note 1-7)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
Carrier to Noise Ratio
Composite Second Order
Composite Triple Beat
Composite Triple Beat
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
Units
6000-SA1
L (km)
65
NTSC 80
7.0/ 7.0
4
16.0
53.0/ 53.0
-65/ -65
-65
-64
6000-SA2
65
PAL 60
7.0/ 7.0
5
16.0
53.0/ 53.0
-65/ -65
-65
-64
Models
6000-SA3
65
NTSC 110
7.0/ 7.0
4
16.0
50.0/ 50.0
-65/ -65
-65
-64
Comments
6000-SA4
65
PAL 89
7.0/ 7.0
5
16.0
50.0/ 50.0
-65/ -65
-65
-64
6000-SA5
65
42 CENELEC
7.0/ 7.0
5
16.0
53.0/ 53.0
-65/ -65
-65
-64
Min.
Min.
Max.
Max. @ +25C
o
Max. @ 0 C to
o
50 C
Min. - Higher
Powers Available
| REV 2011.12
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 6000 Series 1550 nm
Externally Modulated Transmitter
DATASHEET | DECEMBER 2011
FIBER OPTICS
H-type
Property
Performance (Note 1-7)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
Carrier to Noise Ratio
Composite Second Order
Composite Triple Beat
Composite Triple Beat
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
Units
L (km)
Models
6000-H01
6000-H02
80
NTSC 80-Ch
7.0/ 7.0
4
18.0
52.0/ 52.0
-65/ -65
-65
-64
80
PAL 60-Ch
7.0/ 7.0
5
18.0
52.0/ 52.0
-65/ -65
-65
-64
Comments
Min.
Min.
Min.
Max.
Max. @ +25C
Max. @ 0 C to 50 C
o
o
F-type
Property
Performance (Note 1-7)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
Carrier to Noise Ratio
Composite Second Order
Composite Triple Beat
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
Units
6000-F01
L (km)
20
NTSC 80-Ch
7.0/ 7.0
4
21.0
48.0
-58
-58
Models
6000-F02
6000-F03
20
PAL 60-Ch
7.0/ 7.0
5
21.0
48.0
-58
-58
20
NTSC 110-ch
7.0/ 7.0
4
21.0
45.0
-58
-58
Comments
6000-F04
20
PAL 89-Ch
7.0/ 7.0
5
21.0
45.0
-58
-58
Min.
Min.
Max.
Max.
Min.
N-type
Property
Performance (Note 1-7)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
Carrier to Noise Ratio
Composite Second Order
Composite Triple Beat
Composite Triple Beat
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
Units
L (km)
Models
6000-N01
6000-N02
40
NTSC 80-Ch
9.5
4
13.0
52.0
-62
-62
-61
40
PAL 60-Ch
9.5
5
13.0
52.0
-62
-62
-61
Comments
Min.
Min.
Min.
Max.
Max. @ +25C
Max. @ 0 C to 50 C
o
o
Notes:
1. Unless stated otherwise all specifications apply over full temperature range with no digital loading.
2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute
stabilization period.
3. Specifications separated by a slash are port1 / port 2.
4. Units are tested per the Test / Link Configuration Table
5. Noise figure for the EDFA = 4.5 ~ 5.5 dB
6. Corning SMF-28 single mode fiber
7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2
8. With 36 QPSK modulated SAT-IF signals between 950
…
2800 MHz. 27 MHz IF bandwidth
| REV 2011.12
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 6000 Series 1550 nm
Externally Modulated Transmitter
DATASHEET | DECEMBER 2011
FIBER OPTICS
General and Mechanical Specifications
Property
Wavelength
Channel Plan
Optical Connector
Monitoring Interfaces
Operating Temperature
Storage Temperature
Power Consumption
1550 +/-5 nm
Various – See Specification Tabels
SC/APC
100 Base-T Ethernet (SNMP)
Rear Panel RS-232 interface
VFD Screen Front Panel Controls
0C to 50C
-20C to 70C
65W max
EMI:
EN50083-2:2006 (US CATV)
EN55022:2006 (US IT)
EN61000-3-2 (Harmonics)
EN61000-3-3 (Flicker)
FCC: Part 15, Subpart B, class “A” Unintentional
Radiators
ICES-003 (Canada)
AN/NZS 3548, Class A (Australia)
VCCI, Class A (Japan)
GR-2853-CORE
GR-2853-CORE
(VAC)
(VDC)
Dimensions
Input Power Range
20% to 85%
90 to 265 VAC, 50/60 Hz
+/- (36 – 72) VDC
19.0”W x 15.0”D x 1.72”H
17 +/-1 dBmV/ch 80 NTSC channels
15 +/-1 dBmV/ch 110 NTSC channels
18 +/-1 dBmV/ch 60 PAL channels
20 +/-1 dBmV/ch 42 CENELEC channels
16 +/-1 dBmV/ch 89 PAL channels
27 +/-1 dBmV/ch SAT-IF channels
19 +/-2 dBmV/ch 80 NTSC channels
17 +/-2 dBmV/ch 110 NTSC channels
20 +/-2 dBmV/ch 60 PAL channels
18 +/-2 dBmV/ch 89 PAL channels
22 +/-2 dBmV/ch 42 CENELEC channels
29 +/-2 dBmV/ch SAT-IF channels
(width includes 19” front panel ears, depth
includes, connectors, fans & front panel) – see
drawing
Manual mode
Manual mode
Manual mode
Manual mode
Manual mode
Manual mode
CW mode
CW mode
CW mode
CW mode
CW mode
AGC mode
Requirement
Comments
Various Options + ITU-grid available – see
Model Number Information
Custom channel plans available
Other styles available
VFD- (Vacuum Fluorescent Display)
Agency Listings
Safety:
FDA/CDRH Laser Safety Governed by Code
of Federal Regulations Title 21, Volume 8,
Part 1040
IEC 60950-1
IEC 60728-11
Laser IEC 60825-1
CB Certification
In Shipping package
In Shipping package
Non-condensing
Transportation Vibration
Transportation Shock
Operating Humidity
Supply Range
Input Power Range
| REV 2011.12
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 6000 Series 1550 nm
Externally Modulated Transmitter
DATASHEET | DECEMBER 2011
FIBER OPTICS
General and Mechanical Specifications
(continued)
Property
Front Panel RF Gain / OMI
Adjustment Range
CATV Frequency Range
CATV Flatness
CATV Flatness – N-Type
CATV Input impedance
CATV Input Return Loss
CATV Front Panel RF Tap
CATV Front Panel RF Tap Flatness
SAT-IF Frequency Range
SAT-IF Flatness
SAT-IF Input impedance
SAT-IF Input Return Loss
SAT-IF Front Panel RF Tap
SAT-IF Front Panel RF Tap Flatness
Requirement
+2 / -4 dB from nominal setting
Comments
CATV Performance can vary slightly
45MHz – 1003 MHz
+/- 0.50 dB
+/- 0.75 dB
+/- 0.75 dB
75
16dB min
-20 +/- 1 dB down from RF input
+/- 1 dB
950MHz – 2800 MHz
+/- 2 dB
75
10dB min
7 +/- 2.5 dBmV/Ch at 1% OMI/ch
+/- 1 dB
950MHz – 2800 MHz
950MHz – 2800 MHz
45MHz – 1003 MHz
45MHz – 1003 MHz
45MHz - 550MHz
45MHz – 1003 MHz
45MHz – 1003 MHz N-Type
Test/Link Configuration
Property
L-Type
D-Type
S-Type
H-Type
F-Type
N-Type
15 dBm
None
16 dBm
18 dBm
21 dBm
13 dBm
EDFA
25 Km
40 Km
65 Km
80 Km
20 Km
40 Km
Link
1
Received Power
2
0.0 dBm at the receiver
0.0 dBm at the receiver
0.0 dBm at the receiver
0.0 dBm at the receiver
-5.5 dBm at the receiver
0.0 dBm at the receiver
| REV 2011.12
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
(I) Privacy issues: A survey jointly conducted by RFID Journal and market research organization ABI, called "RFID Journal Live", shows that "the biggest benefit of using RFID technology is that it can...
We have previously introduced how to use the LPS22 air pressure sensor in MakeCode. Now let’s introduce how to use it in CircuitPython.First of all, it should be noted that the I2C read and write func...
According to a report published by a market research company, the annual compound growth rate of the semiconductor industry was less than 3% from 1998 to 2002. In contrast, the growth rate of power ma...
[align=left]As a switching power supply engineer, you will often encounter the problem that the MOSFET on the power supply board cannot work properly. First, you need to correctly test to determine wh...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i]The battle for digital TV standards: the market has the final say 2006-7-20The six-year-long dispute over the digital TV terrestr...
I am a hardware novice. I started working in July 2018. Currently, I am only engaged in the design of DC chargers. I am currently responsible for the design of various control circuits in the entire p...
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
