EEWORLDEEWORLDEEWORLD

Part Number

Search

177-714-1-15GP8J5-24SAN

Description
Interconnection Device,
CategoryThe connector    The connector   
File Size436KB,4 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-714-1-15GP8J5-24SAN Overview

Interconnection Device,

177-714-1-15GP8J5-24SAN Parametric

Parameter NameAttribute value
Reach Compliance Code_compli
Connector typeINTERCONNECTION DEVICE
Base Number Matches1
MWDM Micro-D Shielded Cable Assemblies
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly
labor. 100% tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair
177-740 cables are furnished with a full complement of
white/blue twisted pair wires.
Integral Shield Termination–The
connector shell has a
platform to accept Band-It shield termination bands. The
cable shield braid is attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding with
Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully
shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector
shell and secured with a stainless steel
BAND-IT
® clamp. These pre-wired, 100% tested assemblies meet the
requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.
Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either
single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
– A gold-plated
stainless steel ground spring on the pin connector mating face offers
substantial improvement in EMI protection. The graphs compare
identical connectors tested with and without ground springs.
EMI Performance with Ground Spring
SHIELDING EFFECTIVENESS (DB)
SHIELDING EFFECTIVENESS (DB)
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
EMI Performance without Ground Spring
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
FREQUENCY (Hz)
FREQUENCY (Hz)
© 2006 Glenair, Inc.
CAGE Code 06324/0CA77
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
B-8
E-Mail: sales@glenair.com
Android & BlueNRG2
I wrote an Android app and used the following Android code to send a character. I want to know which callback of Bluenrg will be called after sending the character? BluetoothGattService gattService = ...
andiliu ST - Low Power RF
Chip selection for making LED clock products
For the home LED clock, a low-power sleep mode chip was selected mainly to save power, but the effect of the crystal oscillator frequency on the overall current is unknown, and the parameter standards...
一眼呆 51mcu
[Anxinke ESP32 Voice Development Board Special Topic ①] ESP32-A1S Audio Development Board Offline Voice Recognition Control LED Light
Reprint: Anxinke open source team is dedicated to writing and sharing the initial technical exchange of ESP32-A1S offline voice1. Introduction2. Offline speech framework2.1 Algorithm model WakeNet and...
蓝猫淘气 Domestic Chip Exchange
Problems with two types of channel MOS tube circuits
As shown in the figure below, NMOS and PMOS are used as a protection circuit to prevent reverse connection of the power supply. [1] The circuit diagram of the PMOS tube is easy to understand. For the ...
shaorc Analog electronics
The resistor behind the rectifier bridge of this power supply acts as
In the circuit below, what are the functions of the resistors connected behind the rectifier bridge and the three resistors in the red box? What do they mean and what are their main functions?...
kal9623287 Power technology
How to weld this Type-C socket to meet the requirements
As shown in the picture below, does this Type-C female socket need to be mounted with a machine sticker?Some surface mount pins are hidden under the shell, what should I do when doing manual soldering...
kal9623287 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号