Series M
A
Miniature Toggles
General
Specifications
Electrical Capacity (Resistive Load)
Power Level (silver):
6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On & On-None-Off; 3A @ 30V DC for all other circuits
Logic Level (gold):
0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level (gold over silver):
Combines silver & gold ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Contact Resistance:
10 milliohms maximum for silver; 20 milliohms maximum for gold
Insulation Resistance:
1,000 megohms minimum @ 500V DC
Dielectric Strength:
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
Mechanical Life:
100,000 operations minimum; 50,000 operations minimum for flat, locking & splashproof devices
Electrical Life:
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
Angle of Throw:
25°
Toggle:
Bushing:
Case:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Brass with chrome plating
Frame:
Stainless steel
Brass with nickel plating
Support Bracket:
Brass with tin plating
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Terminals:
Copper or brass with silver plating; or copper or brass with gold plating
Pushbuttons
Rockers
Toggles
Other Ratings
Programmable Illuminated PB
Materials & Finishes
Rotaries
Keylocks
Slides
Environmental Data
Operating Temp Range:
–30°C through +85°C (–22°F through +185°F)
Humidity:
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock:
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing:
Splashproof bushing options B3, D3, D8, L3, & L8, which have o-rings inside & outside the
bushing, meet IP67 of IEC60529 Standards.
Mounting Torque:
3.0Nm (26.55 lb
•
in) double nut for large bushing;
1.5Nm (13 lb
•
in) double nut & 0.7Nm (6 lb
•
in) single nut for all other bushings
Soldering:
Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Lever must be in OFF (center) position while soldering.
Cleaning:
These devices are not process sealed. Hand clean locally using alcohol based solution.
Tactiles
Installation
Tilt
Processing
Touch
Indicators
Standards & Certifications
Supplement
Flammability Standards:
UL94V–0 for case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before dash in part number to order UL recognized switch.
All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before dash in part number to order CSA certified switch.
All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum.
Accessories
A48
www.nkk.com
Miniature Toggles
Series M
A
Toggles
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Distinctive
Characteristics
Antirotation design, standard on noncylindrical levers, mates toggle
and bushing; bottom of toggle has two flatted sides which fit into
a complementary opening inside bushing.
Antijamming design protects contacts from damage due
to excessive downward force on actuator.
High torque bushing construction prevents rotation
or separation from frame during installation.
High insulating barriers increase isolation of
circuits in multipole devices and provide
added protection to contact points.
Molded diallyl phthalate case has a UL
flammability rating of 94V-0.
Epoxy sealed terminals prevent entry
of solder flux and other contaminants.
Prominent external insulating barriers
increase insulation resistance and
dielectric strength.
Interlocked actuator block, lever, and interior guide
prevent switch failure due to biased lever movement.
Clinching of frame to case well above base and terminals
provides 1,500V dielectric strength.
Actual Size
Bushing Mount
Page A48
Bracket PC Mount
Page A60
Angle PC Mount
www.nkk.com
Page A66
A49
Series M
Toggles
Bracket PC Mount Miniature Toggles
TYPICAL SWITCH
ORDERING EXAMPLE
A
A
Rockers
Pushbuttons
Programmable Illuminated PB
Poles
1
2
SPDT
DPDT
SP3T
S
S2
S3
E
E2
E4
Small Toggles
.413” (10.5mm) Bat
.200” (5.08mm) Bat
.256” (6.5mm) Bat
.450” (11.4mm) Flatted
.256” (6.5mm) Flatted
.840” (21.3mm) Flatted
.550” (14.0mm) Cone
.640” (16.26mm) Cone
.840” (21.3mm) Cone
A2
S2
A1
S1
Small Bushings
.280” (7.1mm) Smooth with Keyway
.350” (8.9mm) Smooth with Keyway
.280” (7.1mm) Threaded with Keyway
.350” (8.9mm) Threaded with Keyway
Deduct bracket thickness of .020”
(0.51mm) from above dimensions
A
W
G
Contact Materials & Ratings
Silver; Rated
6A @ 125V AC & 3A @ 250V AC
Gold; Rated
0.4VA max @ 28V AC/DC max
Gold over Silver; Rated
6A @ 125V AC & 0.4VA max @
28V AC/DC max
B
C
Optional Caps
For S Bat Toggle
Conical Cap for S Bat Toggle
A
B
C
E
Cap for Locking Lever
No
Code
A
C
G
Nickel Plated Supplied
with Switch
Black
Blue
Red
F
G
Cap Colors
Black
White
Red
Yellow
Green
Blue
Keylocks
Circuits
2
ON
ON
ON
(ON)
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
ON
ON
ON
(ON)
(ON)
(ON)
ON
(ON)
(ON)
3
5
8
9
Q
Q2
Q4
Rotaries
Slides
*
4
*
6
*
7
13
.250” (6.35mm) Straight PC with
.465” (11.8mm) Bracket
.425” (10.8mm) Straight PC with
.630” (16.0mm) Bracket
.964” (24.5mm) Straight PC with
1.150” (29.2mm) Bracket
With Reinforced Bracket
.250” (6.35mm) Straight PC with
.465” (11.8mm) Bracket
.425” (10.8mm) Straight PC with
.630” (16.0mm) Bracket
.750” (19.05mm) Straight PC with
.953” (24.2mm) Bracket
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Locking Lever
L
.201” (5.1mm) Dia. Locking Lever
L2
Bushing For Locking Levers
Smooth with Keyway for Lever Lock
Tactiles
( ) = Momentary
*
3-ON circuits
17
23
Standard Toggle & Bushing Combinations:
25
26
Tilt
Touch
SS2 & S2A2
Indicators
Red Cap on .413”
(10.5mm) Bat Toggle
IMPORTANT:
Switches are supplied without UL,
cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when
ordered with marking on the switch.
Specific models, ratings, & ordering in-
structions are noted on General Specifi-
cations page.
Accessories
Supplement
A1
www.nkk.com
www.nkk.com
A1
Supplement
.250” (6.35mm) Straight PC Terminals
with Bracket .465” (11.8mm) Long
DPDT
ON-NONE-ON Circuit
Accessories
Gold Contacts
with 0.4VA Rating
.350” (8.9mm) Smooth
Bushing with Keyway
Indicators
Touch
M2022SS2G13-BC
Tilt
Tactiles
15
Slides
Toggle dimensions are based on use with
a .350” (8.9mm) bushing; add .070”
(1.78mm) to toggle length when combin-
ing with a .280” (7.1mm) bushing
Terminals
With Bracket
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
M20
2
2
S
S2
G
13
B
C
Toggles
Series M
Toggles
Bracket PC Mount Miniature Toggles
POLES & CIRCUITS
Toggle Position
( ) = Momentary
Connected Terminals
Down
Keyway
A
Down
Pole
Model
Keyway
Throw & Schematics
Up
Note: Terminal numbers are not
actually on the switch.
Pushbuttons
Rockers
Center
Up
Center
SP
Programmable Illuminated PB
M2012
M2013
M2015
M2018
M2019
M2022
M2023
M2025
M2028
M2029
ON
ON
ON
(ON)
ON
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
ON
ON
(ON)
(ON)
(ON)
2-3
OPEN
2-1
SPDT
3
2 (COM)
1
DP
2-3 5-6
OPEN
2-1 5-4
DPDT
3
2
(COM)
1
6
5
4
For 3 Throw (3-On)
Pole
Model
M2024
M2026
M2027
Connected Terminals & Schematics
Down
ON
(ON)
ON
External
Connection
2 (in)
5
Keylocks
Center
ON
ON
ON
External
Connection
2 (in)
5
Up
ON
(ON)
(ON)
External
Connection
2 (in)
5
External Connection
The SP3T model utilizes
a double pole base.
(out)
External
Conn
6
5
4
3
2
1
SP
Rotaries
Slides
1 (out)
3 4 (out) 6 (out)
1 (out)
3 4 (out) 6 (out)
1 (out)
3 4 (out) 6 (out)
2-3 5-6
2-3 5-4
2-1 5-4
External
connection
must be made
during field
installation.
Common
(in)
(out)
(out)
SMALL TOGGLES
Tactiles
Important:
Toggle length changes based on
bushing selected. All illustrations
are shown with .350” (8.9mm)
long bushing. When using a .280”
(7.1mm) long bushing, toggle length
increases .070” (1.78mm).
Standard Material & Finish:
Brass with Bright Chrome
Contact factory for optional finishes.
.256” (6.5mm)
Flatted
S
.413”
(10.5mm)
Bat
25°
S2
.200”
(5.08mm)
Bat
S3
.256”
(6.5mm)
Bat
E
(5.08)
.200
.450”
(11.4mm)
Flatted
(2.54)
.100
(11.4)
.450
25°
Tilt
(2.8) Dia
.110
(10.5)
.413
(2.7) Dia
.106
(5.08)
.200
25°
25°
(2.7) Dia
.106
(6.5)
.256
Touch
Indicators
E2
E4
(5.0)
.197
.840” (21.3mm)
Flatted
(2.5)
.098
25°
Q
.550” (14.0mm)
Cone
Q2
.640” (16.26mm)
Cone
Q4
.840” (21.3mm)
Cone
25°
Accessories
(3.1) Dia
.122
(4.2)
.165
(2.5)
.098
(6.5)
.256
25°
(21.3)
.840
(14.0)
.550
25°
(3.1) Dia
.122
25°
(3.1) Dia
.122
(16.26)
.640
(21.3)
.840
Supplement
A62
www.nkk.com
Bracket PC Mount Miniature Toggles
SMALL BUSHINGS
A2
.280” (7.1mm)
Smooth with Keyway
(0.8)
.031
(6.2) Dia
.244
(8.0) Dia
.315
(8.0) Dia
.315
(0.9)
.035
Series M
A
(0.8)
.031
(6.2) Dia
.244
(0.9)
.035
(2.5)
.098
(0.5)
.020
(2.5)
.098
(0.5)
.020
When using this bushing, toggle length
is increased by .070” (1.78mm).
A1
.280” (7.1mm)
Threaded with Keyway
(0.8)
.031
1/4-40 Thd
(0.9)
.035
S1
.350” (8.9mm)
Threaded with Keyway
(0.8)
.031
1/4-40 Thd
(0.9)
.035
(2.5)
.098
(0.5)
.020
(2.5)
.098
(0.5)
.020
When using this bushing, toggle length is increased
by .070” (1.78mm). Maximum Panel Thickness
with Standard Hardware: .031” (0.8mm)
Panel Cutouts
Maximum Panel Thickness with
Standard Hardware: .102” (2.6mm)
Standard Hardware:
2 Hex Nuts (AT513H)
1 Lockwasher (AT509)
1 Locking Ring (AT507H)
For dimensions, see Accessories
& Hardware section.
(0.6)
.024
LOCKING LEVER & BUSHING
LL2
Smooth
with Keyway
(2.5)
.098
Locking Mechanism
on-none-on
on-none-(on)
on-off-(on)
on-on-(on)
on-off-on
on-on-on
(on)-off-(on)
(on)-on-(on)
(0.8)
.031
(8.0) Dia
.315
2 positions lock
25°
(5.1) Dia
.201
(16.5)
.650
1 position locks
2 positions lock
3 positions lock
1 position locks
(8.0)
.315
(15.0)
.591
(4.6) Dia
.181
(6.2) Dia
.244
(0.9)
.035
Supplied with Cap AT427
Material & Finish:
Brass with Nickel Plating
Lever Material & Finish:
Brass with Chrome Plating
www.nkk.com
(0.5)
.020
G
Blue
A63
Supplement
(9.3) (7.0)
.366 .275
A
Black
C
Red
Accessories
No Code
Cap for Locking Lever
Color Codes for Optional
Anodized Aluminum Caps
Indicators
Touch
Tilt
Tactiles
For A2, S2, A1,
or S1 Bushing
with Keyway
(5.6)
.220
(6.5) Dia
.256
For A1 or
S1 Bushing
with Locking Ring
(6.5) Dia
.256
(2.2) Dia
.087
(6.5)
.256
Slides
Rotaries
(7.1)
.280
(8.9)
.350
Keylocks
(8.0) Dia
.315
(8.0) Dia
.315
Programmable Illuminated PB
(7.1)
.280
(8.9)
.350
Pushbuttons
Rockers
S2
.350” (8.9mm)
Smooth with Keyway
Toggles
MEMS sensors
京公网安备 11010802033920号
EEWORLD
