EEWORLDEEWORLDEEWORLD

Part Number

Search

1812Y2500104KETT01

Description
Ceramic Capacitor, Multilayer, Ceramic, 250V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.1uF, Surface Mount, 1812, CHIP
CategoryPassive components    capacitor   
File Size253KB,1 Pages
ManufacturerSyfer
Environmental Compliance  
Download Datasheet Parametric View All

1812Y2500104KETT01 Overview

Ceramic Capacitor, Multilayer, Ceramic, 250V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.1uF, Surface Mount, 1812, CHIP

1812Y2500104KETT01 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerSyfer
package instruction, 1812
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance0.1 µF
Capacitor typeCERAMIC CAPACITOR
dielectric materialsCERAMIC
JESD-609 codee3
Installation featuresSURFACE MOUNT
multi-layerYes
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formSMT
method of packingTR, 7 INCH
positive tolerance10%
Rated (DC) voltage (URdc)250 V
GuidelineAEC-Q200
size code1812
surface mountYES
Temperature characteristic codeX7R
Temperature Coefficient15% ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
X7R
Tandem capacitors
Tandem Capacitors have been designed as a
fail safe range using a series section internal
design, for use in any application where short
circuits would be unacceptable. When combined
with Syfer FlexiCap™ termination, Syfer Tandem
capacitors provide an ultra robust and reliable
component, for use in the most demanding
applications.
Tandem capacitor - Untested
Tandem capacitor - Qualification included cracking the
components by severe bend tests. Following the bend tests
cracked components were subjected to endurance / humidity
tests, with no failures evident due to short circuits.
Note: Depending on the severity of the crack, capacitance loss
was between 0% and 50%.
Max capacitance in nF (X7R only)
0603
16V
25V
50/63V
100V
200/250V
12
10
6.8
2.2
1.0
0805
47
39
33
10
4.7
1206
150
120
100
47
22
1210
270
220
180
82
47
1812
560
470
390
220
100
2220
1200
1000
680
470
220
2225
1500
1200
1000
680
330
Ordering information - Tandem capacitors
1206
Chip
size
0603
0805
1206
1210
1812
2220
2225
Y
Termination
Y
= Polymer
Termination
FlexiCap™
050
Voltage
016 = 16V
025 = 25V
050 = 50V
063 = 63V
100 = 100V
200 = 200V
250 = 250V
0104
Capacitance in
picofarads (pF)
First digit is 0. Second
and third digits are
significant figures of
capacitance code.
The fourth digit is
number of zeros
following.
Example:
0104 = 100000pF
K
Capacitance
tolerance
K = ±10%
E
Dielectric
codes
X
= X7R
E
= X7R
(AEC-Q200
product)
T
Packaging
T
= 178mm
(7”) reel
R
= 330mm
(13”) reel
T01
Suffix
Syfer
Tandem
capacitor
25
Motor Control Advanced 3——PID Cascade Control (with full code download)
The first two articles introduced [PID speed control](https://en.eeworld.com/bbs/thread-1166004-1-1.html) and [PID position control](https://en.eeworld.com/bbs/thread-1166782-1-1.html), which are used...
DDZZ669 Motor Drive Control(Motor Control)
[Evaluation of domestic FPGA Gaoyun GW1N-4 series development board] ——9. Internal OSC and rPLL IP core test
[i=s]This post was last edited by gs001588 on 2022-1-8 12:16[/i][Evaluation of domestic FPGA Gaoyun GW1N-4 series development board] ——9. Internal OSC and rPLL IP core testGW1N-4, GW1N-4B and other se...
gs001588 Domestic Chip Exchange
Zero-Drift Amplifiers: Features and Benefits
Zero-drift amplifiers use a unique self-correcting technique to provide ultra-low input offset voltage (Vos) and near-zero input offset voltage drift over time and temperature (dVos/dT) for general-pu...
Jacktang Analogue and Mixed Signal
Interference issues
It is a 1MHZ PWM signal. The 12V side is stepped down to 5V and fed to the microcontroller. It is found that the 5V power supply has more burrs, causing the PWM output waveform to be distorted. 12V 24...
tangwei8802429 Analog electronics
Help, the SD card cannot communicate normally, and the measured pin voltage is abnormal
When I read and write the SD card, FR_NOT_READY is always returned. The waveforms of the CD and DATA0 pins measured with an oscilloscope are abnormal. The SD card is powered by 3.3V and the processor ...
littleshrimp Integrated technical exchanges
Implement PID using FPGA and simulate with modelsim
It is very common to use a single-chip microcomputer. However, in FPGA, due to floating-point arithmetic problems, it is troublesome to use PID. The following is a PID Verilog program I designed. It s...
wstcllx EE_FPGA Learning Park

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号