Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
How knowledgeable are you? What kind of electronic device is this (the IC circled in the picture below)? It is used in the power supply. Is it an inductor?
I've seen it before, don't know what it was....
The following represents personal opinions, which may not be completely objective. What I received is the F103 development board. The board is not big and is a black development board. I don't like bl...
1. Main features of choppers The main features of choppers are as follows: (1) There is a single brake chopper available for each power range, and no parallel connection is required; (2) It can be ...
[i=s]This post was last edited by qwqwqw2088 on 2022-7-18 09:08[/i]There are often different opinions on whether copper should be placed at the bottom of the inductor of a DC/DC power supply. One view...
This Spring Festival Gala, which has the highest AI content in history, has ended perfectly for a week.
Perhaps the high-tech Spring Festival Gala caught people's attention, and the ratings of...[Details]
SEGGER and Geehy collaborate to fully support APM32 series microcontrollers
Monheim, Germany - September 15, 2022
As part of the collaboration with Geehy Pol...[Details]
For newly purchased inverters and inverters in use, it is often necessary to measure the filter current or voltage at each time, so as to change the current situation of most users only qualitativel...[Details]
1. Introduction In this article, we use the key as the input device to test the GPIO input function of the Freescale XEP100 microcontroller. The corresponding hardware circuit is shown in the...[Details]
Just as we have become accustomed to scanning code payment, more and more offline face-scanning payment devices are quietly changing our payment habits. Compared with scanning code payment, although ...[Details]
The STM32F103 series has only 60 maskable interrupts (68 in the 107 series) Interrupt Management Methods First, the STM32 interrupts are grouped into groups 0 to 4. At the same time, a preemption...[Details]
Before the invention of dynamically adjustable high power linear regulators, LED electronics designers had two main options for configuring multiple LED strings: Use a switching regulator to regulate...[Details]
There is no such thing as a one-time solution in the world, so don't think that any programming pattern can "kill" all program structures. The discussion of LabVIEW programming patterns in this articl...[Details]
This article introduces the use of I2C memory. It mainly introduces the AT24CXX series devices, which are divided into two categories, mainly based on the storage capacity address. One category is AT2...[Details]
Abstract: The demand for ADAS functions in the automotive industry is growing, and anti-fatigue driving is a hot topic. Face recognition is the basis for detecting the driver's status. Only by quickl...[Details]
According to foreign media reports, semiconductor expert Nexperia announced the launch of the industry's first A-selection Zener diode series: BZT52H-A (SOD123F) and BZX384-A (SOD323). Compared with ...[Details]
A histogram is also called a column chart. It is a graph that uses a series of rectangles of equal width and different heights to represent data. As shown in Figure 1(a), the width of the rectangle...[Details]
USB charger kit, also known as MP3MP4 charger, input AC160-240V, 50/60Hz, rated output: DC 5V
250mA (label sticker is 500mA, if you want to output a higher current for a long time, plea...[Details]
On December 18, Zhichun Technology announced that the company and Ningbo Yushan Investment Management Co., Ltd. (hereinafter referred to as "Ningbo Yushan") jointly invested in a private equity inves...[Details]
According to a new study from Rice University, the secret to promoting the longevity of lithium-ion batteries is to crush silicon powder. Experts have been trying to turn silicon into rechargeable ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
