PH1-7LALC3722 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-7LALC3722

PH1-7LALC3722: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-7LALC3722 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-7LALC3722 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Connection Type	LC/SPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1551 nm
Nominal optical power output	1.584 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Stabilized DC boost circuit

Electrical schematic diagram of M7120 surface grinder (1)

Binary Parallel Addition and Subtraction Circuit

Programmable counter

Ordinary ZCT-PWM converter

Using HT-7610A infrared sensor music socket control circuit

Gizwits Intelligent Gateway Solution enables interconnection of different brands and protocols: [i=s]This post was last edited by Maoqiu Dada on 2021-12-29 14:36[/i]There are now a wide variety of smart devices on the market, using a variety of communication protocols. Combining these devices in...; 毛球大大 RF/Wirelessly

What information does the signal measured by a lock-in amplifier have?: What information does the signal measured by the lock-in amplifier contain? What other information does the measured signal carry?...; senkyi Analog electronics

50-300MHz Sine Output VCO Design: The system needs to use a 50-300MHz swept frequency sine signal output, but the RF circuit is rarely used. After searching for some information, I found that there are two main solutions. One is discr...; tziang RF/Wirelessly

How to perform gas flow detection: The purpose of detecting the gas flow is to detect the working status of the speed-regulated suction pump. The rotation speed is adjusted to maintain a stable flow rate in different environments. The ...; sfcsdc Analog electronics

Qorvo Online Design Conference | How to resolve V2X spectrum coexistence challenges: V2X, Wi-Fi and 5G are widely acknowledged as enablers of autonomous driving technology. The challenge now is how these technologies can work together and coexist despite spectrum interference that can...; 兰博 RF/Wirelessly

Video explains the triggering modes of oscilloscopes and what they mean: The principle and usage of each trigger mode are explained in the form of video, including edge trigger, pulse width trigger, logic trigger, N edge trigger, runt trigger, slope trigger, and timeout tr...; Micsig麦科信 Test/Measurement

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components