EEWORLDEEWORLDEEWORLD

Part Number

Search

X5325V14Z-T

Description
IC,SERIAL EEPROM,4KX8,CMOS,TSSOP,14PIN,PLASTIC
CategoryPower/power management    The power supply circuit   
File Size342KB,20 Pages
ManufacturerRenesas Electronics Corporation
Websitehttps://www.renesas.com/
Environmental Compliance  
Download Datasheet Parametric View All

X5325V14Z-T Overview

IC,SERIAL EEPROM,4KX8,CMOS,TSSOP,14PIN,PLASTIC

X5325V14Z-T Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerRenesas Electronics Corporation
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
JESD-609 codee3
Humidity sensitivity level1
Peak Reflow Temperature (Celsius)225
Terminal surfaceMATTE TIN
Maximum time at peak reflow temperatureNOT SPECIFIED
®
X5323, X5325
(Replaces X25323, X25325)
Data Sheet
June 30, 2008
FN8131.2
CPU Supervisor with 32kBit SPI EEPROM
These devices combine four popular functions, Power-on
Reset Control, Watchdog Timer, Supply Voltage Supervision,
and Block Lock Protect Serial EEPROM Memory in one
package. This combination lowers system cost, reduces
board space requirements, and increases reliability.
Applying power to the device activates the power-on reset
circuit which holds RESET/RESET active for a period of
time. This allows the power supply and oscillator to stabilize
before the processor can execute code.
The Watchdog Timer provides an independent protection
mechanism for microcontrollers. When the microcontroller
fails to restart a timer within a selectable time out interval,
the device activates the RESET/RESET signal. The user
selects the interval from three preset values. Once selected,
the interval does not change, even after cycling the power.
The device’s low V
CC
detection circuitry protects the user’s
system from low voltage conditions, resetting the system
when V
CC
falls below the minimum V
CC
trip point.
RESET/RESET is asserted until V
CC
returns to proper
operating level and stabilizes. Five industry standard V
TRIP
thresholds are available, however, Intersil’s unique circuits
allow the threshold to be reprogrammed to meet custom
requirements or to fine-tune the threshold for applications
requiring higher precision.
Features
• Selectable watchdog timer
• Low V
CC
detection and reset assertion
- Five standard reset threshold voltages
- Re-program low V
CC
reset threshold voltage using
special programming sequence
- Reset signal valid to V
CC
= 1V
• Determine watchdog or low voltage reset with a volatile
flag bit
• Long battery life with low power consumption
- <50µA max standby current, watchdog on
- <1µA max standby current, watchdog off
- <400µA max active current during read
• 32kbits of EEPROM
• Built-in inadvertent write protection
- Power-up/power-down protection circuitry
- Protect 0, 1/4, 1/2 or all of EEPROM array with Block
Lock
protection
- In circuit programmable ROM mode
• 2MHz SPI interface modes (0,0 and 1,1)
• Minimize EEPROM programming time
- 32-byte page write mode
- Self-timed write cycle
- 5ms write cycle time (typical)
• 2.7V to 5.5V and 4.5V to 5.5V power supply
operation
• Available packages
- 14 Ld TSSOP, 8 Ld SOIC, 8 Ld PDIP
• Pb-free (RoHS compliant)
Block Diagram
WATCHDOG TRANSITION
DETECTOR
WP
SI
SO
SCK
CS/WDI
DATA
REGISTER
COMMAND
DECODE AND
CONTROL
LOGIC
V
CC
THRESHOLD
RESET LOGIC
PROTECT LOGIC
RESET/RESET
STATUS
REGISTER
8kBITS
8kBITS
16kBITS
EEPROM ARRAY
RESET AND
WATCHDOG
TIMEBASE
X5323 = RESET
X5325 = RESET
WATCHDOG
TIMER RESET
V
CC
V
TRIP
+
-
POWER-ON AND
LOW VOLTAGE
RESET
GENERATION
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005, 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
Is there anything wrong with this STC procedure?
IapErase(0x2000);for(i=0;i64;i++){IapProgram(0x2000+i,i);}b=IapRead(0x2001);This is the EEPROM program of STC. Logically, the value of b should be 1, right? Why is it 63?...
sky999 51mcu
Testing of heating power of NOx sensor
Testing of heating power of NOx sensorSensors based on the Nerst equation and using zirconium oxide ( YSZ ) as the base need to work at high temperatures. This type of sensor is widely used in the fie...
eldzhou Automotive Electronics
IoT access terminal
Introduction The work collects voltage through ADC and transmits it to the cloud server through the 4G module. The protocol uses TCP transparent transmission, and the data is retained in the cloud pla...
lehuijie GD32 MCU
How to Measure Cable Impedance and Loss Using a Vector Network Analyzer
Step one: calibration. In addition to the cable to be tested, another auxiliary cable is required. The ZVB8 vector network analyzer (hereinafter referred to as VNA) we use has two ports: Port1 and Por...
安泰测试设备 Test/Measurement
Make Magazine: Getting started with Python on hardware
Make magazine has a new article about getting started with Python on hardware. It discusses MicroPython and CircuitPython with some examples. Finally, it covers some large projects using Python on har...
dcexpert MicroPython Open Source section
Does the LCD module need to be grounded when used?
This morning, the company's customer service transferred a call from a customer to me for help, saying that during the debugging of a newly proofed device, the display screen had garbled characters an...
罗姆液晶技术站 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号