A brings Illumination Grade LED light sources to the lighting market. It has never been simpler
to design LED solutions and bring them to market. With hot testing and color binning, every LUXEON A
is tested and specified at real world operating conditions, Tj 85°C. With
Freedom From Binning,
every
LUXEON A LED falls within a single 3 step MacAdam ellipse centered on the black body curve and now,
luminaire manufacturers can be confident in color consistency from LED to LED. There’s never been a
more supportable and consistent light emitting diode. The superior quality of light, light output, and real
world efficacy enable leading performance and efficient solution development in a wide variety of segments
including retrofit bulbs, office, hospitality, school, and home lighting.
•
Freedom From Binning
for superior quality of light
•
Hot tested and color binned at Tj 85°C
•
Maximum light output and lowest cost of light
•
Specified color over angle
•
Simplified design and accelerated time to market.
Table of Contents
General Product Information .....................................................................................................................................3
Absolute Maximum Ratings ...................................................................................................................................7
Pad Configuration ................................................................................................................................................10
Solder Pad Design..................................................................................................................................................10
Relative Spectral Distribution vs. Wavelength Characteristics .........................................................................11
Typical Light Output Characteristics over Temperature ....................................................................................14
Typical Forward Current Characteristics ..............................................................................................................15
Current Derating Curves..........................................................................................................................................16
Product Binning and Labeling ...................................................................................................................................22
LUXEON A 3-step MacAdam Ellipse Color Definition ................................................................................24
Forward Voltage Bins ..................................................................................................................................................25
LUXEON A Datasheet DS100 20121215
2
General Product Information
Product Nomenclature
LUXEON A emitters are tested and binned “hot” under conditions comparable to those found in “real-world” lighting products.
The test conditions for LUXEON A are 700 mA D.C. with junction temperature at 85ºC.
The part number designation for the LUXEON A emitters is explained as follows:
L X HA - B C D E
Where:
A — designates minimum CRI performance (value 8 = 80 minimum and value 9 = 90 minimum)
B — designates radiation pattern (value P for Lambertian)
C — designates color (value W = White)
D & E — designates nominal ANSI CCT (value 27 = 2700K, 30 = 3000K, 40 = 4000K and 50 = 5000K)
Therefore products tested and binned at 700 mA follow the part numbering scheme:
L X H x - PW x x
Lumen Maintenance
LUXEON A products are tested in compliance with LM-80. Please visit http://www.philipslumileds.com/support/documentation/lumen-maintenance
or contact your local Philips Lumileds Technical Solutions Manager for TM-21 extrapolations or other support.
Environmental Compliance
Philips Lumileds is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON A is compliant to
the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS and REACH directives.
Philips Lumileds will not intentionally add the following restricted materials to the LUXEON A: lead, mercury, cadmium, hexavalent chromium,
polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE).
LUXEON A Datasheet DS100 20121215
3
Product Selection
Product Selection Guide for LUXEON A Emitters
Junction Temperature = 85°C
Table 1.
Typical Performance Characteristics at 350 mA, 700 mA, and 1000 mA for LUXEON A, Junction Temperature = 85°C
CRI
Part
Number
LXH8-PW27
LXH8-PW30
LXH9-PW30
LXH8-PW40
LXH8-PW50
Nominal
ANSI CCT
2700K
3000K
3000K
4000K
5000K
@ 700 mA
Min.
80
80
90
80
80
Typ.
85
85
95
85
85
Lum Flux (lm)
Min. @
700 mA
140
150
120
160
170
Typ. Lum Flux (lm)
@
350 mA
89
97
75
102
106
@
160
174
135
183
190
@
218
237
184
249
258
700 mA 1000 mA
Typ. Forward Voltage (V
f
)
@
350 mA
2.72
2.72
2.72
2.72
2.72
@
2.81
2.81
2.81
2.81
2.81
@
2.85
2.85
2.85
2.85
2.85
700 mA 1000 mA
Typ. Efficacy (lm/W)
@
93
102
79
107
111
@
81
88
69
93
97
@
76
83
64
87
91
350 mA 700 mA 1000 mA
LUXEON A Datasheet DS100 20121215
4
Optical Characteristics
LUXEON A at Test Current
[1]
Junction Temperature = 85°C
Table 2.
Color Temperature
CCT
Nominal
ANSI CCT
Part
Number
Typical
Typical
Total
Included
Angle
[2]
(degrees)
u
0.90V
Typical
Viewing
Angle
[3]
(degrees)
2u
1/2
120
120
120
120
120
2700K
LXH8-PW27
2725K
160
3000K
LXH8-PW30
3045K
160
3000K
LXH9-PW30
3045K
160
4000K
LXH8-PW40
3985K
160
5000K
LXH8-PW50
5028K
160
Notes for Table 2:
1. Test current is 700 mA D.C. for all LXH8-PWxx emitters.
2. Total angle at which 90% of total luminous flux is captured.
3. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.
We need to know that variables are just abstract names of memory addresses. In statically compiled programs, all variable names will be converted into memory addresses during compilation. The machine ...
I feel that Infineon's philosophy has always been to make complex and extremely professional development tools simple and easy to use, including sensor development boards, MCU development boards, moto...
Is there any expert who can give me some advice? I can only understand simple circuit diagrams with few lines, and I can't understand complex circuit diagrams with many lines at all. Where should I st...
[size=4]1) It can run in single step, but will always return to address 0 when running continuously: Watchdog is not turned off, and continuous running will reset the DSP back to address 0. [/size] [s...
Proximity sensors and existing solutions Proximity sensors play an important role in our lives and are widely used in smart home appliances, such as faucets that automatically sense water, air conditi...
Compared with traditional bulk devices, flexible electronic technology has brought revolutionary changes. This technology makes electronic devices thin, soft, and even elastic, similar to paper or ...[Details]
The simplest actual circuit of 5V/5W switching power supply is as shown in the figure. TOP210 (IC1) in the picture is a three-terminal PWM switch. IC1 contains PWM controller, power MOSFET and vari...[Details]
When writing applications, we usually use a malloc/free series of functions to manage memory. The memory space allocated in this way is allocated from the stack space of the application. Generally spe...[Details]
According to Jiwei.com news (text/Digital Control), MIUI’s advertisements have always put off many consumers who like Xiaomi, and now the official has finally decided to make changes to MIUI’s advert...[Details]
Some measurements that were "cutting-edge" a few years ago are now routine. Almost every engineer can tell of a time when they tracked down a problem caused by a few nanoseconds of delay or an almost...[Details]
Precautions for on-site use 1. On-site use conditions should meet the requirements of the instrument's technical parameters. Correctly select the instrument range, the measured pressure should not ex...[Details]
Have you ever been driven crazy by your phone's battery dropping to 20% when you need it most? It is reported that the top ten most advanced breakthrough technologies can make your phone battery perf...[Details]
The main purpose of the textile airflow resistance tester: The textile airflow resistance tester of Shanghai Chengwei Instrument Technology Co., Ltd. is used to measure the air penetration resistance...[Details]
孟樸：尊敬的柯瑞文董事长、各位领导、来宾、新闻界的朋友们，大家下午好，很高兴和大家齐聚广州。 First of all, on behalf of Qualcomm, I would like to express my sincere congratulations to China Telecom and Chairman Ke Ruiwen on the successful c...[Details]
At present, there are two ISO standards in the field of 13.56 MHz wireless radio frequency identification technology in my country, one is ISO14443 and the other is ISO15693. ISO14443 defines two type...[Details]
The reporter learned on the 25th that the Kunming New Energy Vehicle Operation Information Management and Service Platform, which was prepared and built by the Kunming Development Investment Group,...[Details]
Failure phenomenon:
English: Trying to handshake with MCU/MCU...
Failed to open serial port!
English: The serial port has been opened by another program or the serial port does not exist.
Sol...[Details]
STM32CubeMX is a popular development tool that can greatly improve our transplantation efficiency and thus improve development efficiency, but there are still some small pitfalls that we need t...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
0. Write in front
3D object detection is a very important basic task for autonomous driving. Today, I would like to recommend a recent review of 3D object detection.
2. Summary
...[Details]
Altera SoC
京公网安备 11010802033920号
EEWORLD
