ABM83-FREQ-18-R050-B-4-H-T datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> ABM83-FREQ-18-R050-B-4-H-T

ABM83-FREQ-18-R050-B-4-H-T: DescriptionParallel - Fundamental Quartz Crystal, 30MHz Min, 60MHz Max, MINIATURE, CERAMIC, SMD, 4 PIN; CategoryPassive components Crystal/resonator; File Size328KB，2 Pages; ManufacturerAbracon; Websitehttp://www.abracon.com/index.htm; Environmental Compliance

Download Datasheet Parametric View All

ABM83-FREQ-18-R050-B-4-H-T Overview

Parallel - Fundamental Quartz Crystal, 30MHz Min, 60MHz Max, MINIATURE, CERAMIC, SMD, 4 PIN

ABM83-FREQ-18-R050-B-4-H-T Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Abracon
package instruction	MINIATURE, CERAMIC, SMD, 4 PIN
Reach Compliance Code	compliant
Other features	TAPE AND REEL
Ageing	5 PPM/FIRST YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	10 µW
frequency stability	0.0035%
frequency tolerance	30 ppm
JESD-609 code	e4
load capacitance	18 pF
Installation features	SURFACE MOUNT
Maximum operating frequency	60 MHz
Minimum operating frequency	30 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
physical size	L3.2XB2.5XH0.55 (mm)/L0.126XB0.098XH0.022 (inch)
Series resistance	50 Ω
surface mount	YES
Terminal surface	Gold (Au) - with Nickel (Ni) barrier

Preview

Download Datasheet

View All

ULTRA MINIATURE CERAMIC SMD CRYSTAL

ABM8

FEATURES:

• Low in height; suitable for thin equipment.

• Ceramic package and metal lid assures high reliability.

• Tight tolerance and stability available.

• Suitable for solder reflow.

• High precision crystal, fundamental mode.

3.2 x 2.5 x 0.8mm

| | | | | | | | | | | | | | |

APPLICATIONS:

• High density applications.

• Modems, communication and test equipment.

• PMCIA, Wireless applications.

STANDARD SPECIFICATIONS:

PARAMETERS

Frequency Range

Operation Mode

Operating Temperature

Storage Temperature

Frequency Tolerance @ 25°C

Frequency Stability over Temp.

Equivalent Series Resistance

Shunt Capacitance C

Load Capacitance C

Drive Level

Aging at 25°C First Year

Insulation Resistance

10.00 MHz - 60.00 MHz

Fundamental

-10°C to + 60°C (see options)

- 55°C to + 125°C

± 50 ppm max. (see options)

See Table 1

7pF max.

18pF (see options)

100µΩ max., 10µΩ correlation

± 5ppm max.

500MΩ min. @ 100Vdc ± 15V

MARKING:

- XX.X

- A ZYX

(Frequency in MHz)

(ZY:date code, e.g. L2;

Z: month A to L;

Y: last digit of year;

X: Traceability code)

OUTLINE DRAWING:

Please see Table 2 below for height and chamfer information.

TABLE 1

FREQ (MHz)

ESR (

Ω

)max.

10.000 - 15.999

200

16.000 - 19.999

100

20.000 - 29.999

30.000 - 60.000

TABLE 2

Height (mm)

ABM8

0.70+/-0.10

ABM81

0.65+/-0.05

ABM82

0.60+/-0.10

ABM83

0.55+/-0.05

Chamfer PIN #

Dimensions: inch (mm)

ABRACON IS

ISO 9001 / QS 9000

CERTIFIED

30332 Esperanza, Rancho Santa Margarita, California 92688

tel 949-546-8000

fax 949-546-8001

| www.abracon.com

Revised: 11.27.06

Recommended Resources

Various DA converters with simple structures a

Touch delay light circuit using music IC

Triangular wave and square wave generator circuit diagram installed with NE555

Loop timer circuit

Simple parallel charger circuit diagram

A wireless remote control circuit

Reversible USB port: I bought a mobile power board a few days ago. I didn’t think much of it at first, but later I found that the USB A port was quite special. It can be plugged in both ways....; dcexpert Making friends through disassembly

Why does the power consumption of stm32L0 increase after it enters STOP mode again after being woken up by an external interrupt in STOP mode?: The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...; StruggleMySen stm32/stm8

[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2: [i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...; wangran_95 TI Technology Forum

Using registers to do STM8 UART1 error request help: [i=s]This post was last edited by zhang520 on 2021-10-21 15:08[/i]Error[Li006]: duplicate definitions for "_interrupt_21"; Change 21 to 20 and the system will run fine...; zhang520 stm32/stm8

BearPi-HM Nano Development Board Review 0 Unboxing and Development Environment Setup: [i=s]This post was last edited by symic on 2022-3-20 19:42[/i]I am very happy and surprised to get the opportunity to review the BearPi-HM Nano development board. Thanks to Nanjing BearPi Intelligent ...; symic Linux and Android

XP power management issues: There is no "Enable Advanced Power Management" item in my mind. What is the reason and how to solve it? Before I came here to ask questions, I tried the following methods but they didn't work: 1. In t...; zbz0529 Power technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components