REVISION D
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. BURR ALLOWANCE: .003[0.08] MAX.
3. PARTS TO BE MOLDED TO POSITION.
4. MINIMUM PULLOUT FORCE: 5 lbs [2.22 N].
5. CONTACT MUST BE INSERTED UNTIL RETENTION FEATURE LOCKS
INTO PLACE.
6. ALL FINISHED GOODS ARE TO BE ELECTRICAL TESTED INCLUDING HI-POT TEST.
7. TINNED COPPER WIRE CONTAINS LEAD.
8. PARTS ARE TO BE LAYER PACKAGED.
9.
CONTACTS OFFSET FOR POLARIZATION.
MMSS-XX-XX-X-XX.XX-X-X-XXX
No OF POSITIONS
-02 THRU -10
WIRE GAUGE (AWG)
-20
-22
-24
-26
-28
-30
PLATING SPECIFICATION
-F: FLASH SELECTIVE (USE C-179-XX-F)
-L: LIGHT SELECTIVE (USE C-179-XX-L)
-S: SELECTIVE (USE C-179-XX-S)
OPTION
[AVAILABLE ON -D END OPTION ONLY
& APPLIES TO END 2 HOUSING]
-LUS: LATCH UP, STRAIGHT
-LDS: LATCH DOWN, STRAIGHT
OPTION
*-K: KEYED POLARIZATION
(USE IPD1-XX-S-K)
(SEE FIG. 3, SHEET 2)
DO NOT
SCALE FROM
THIS PRINT
D
02 01
(No OF POS x .100[2.54])
+ .055[1.40] REF
C
L
.200 5.08
REF
.300 7.62
REF
.010 0.25 REF
(SEE NOTE 9)
"A"
END OPTION
-S: SINGLE END
-D: DOUBLE END(MUST CHOOSE FROM
LAST SET OF OPTIONS.)
ASSEMBLED LENGTH
SPECIFY IN INCHES [USE DWC-XX-XX]
(SINGLE END: 03.00[76.2] INCH MINIMUM,
DOUBLE END: 03.25[82.6] INCH MINIMUM)
IPD1-XX-S
* NOT RELEASED FOR PRODUCTION
.505 12.83
REF
C-179-XX-X
.285 7.24
REF
C1
XX.XX .125[3.18]
= DWC + .250[6.35]
DWC-XX-10-300
C2
XX.XX .125[3.18]
= DWC + .500[12.70]
"A"
SECTION "A"-"A"
FIG. 1
MMSS-05-22-X-XX.XX-S SHOWN
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
FIG. 2
MMSS-05-22-X-XX.XX-D-LUS SHOWN
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.XX: .01 [0.3]
2
.XXX: .005 [0.13]
.XXXX: .0020 [0.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
HOUSING: NYLON 6/6, COLOR: WHITE
CONTACT: PHOS BRONZE
CABLE; INSULATION: PVC
WIRE: TINNED COPPER
F:\DWG\MISC\MKTG\MMSS-XX-XX-X-XX.XX-X-X-XXX-MKT.SLDDRW
.100[2.54] SOCKET DISCREET CABLE ASSEMBLY
BY:
DEAN P
MMSS-XX-XX-X-XX.XX-X-X-XXX
05/03/2005
SHEET
1
OF
2
REVISION D
LATCH-
END 2
LATCH-
END 1
LATCH-
END 1
[LATCH UP- CABLE STRAIGHT]
-LUS
LATCH-
END 2
[LATCH DOWN- CABLE STRAIGHT]
-LDS
-K: KEYED POLARIZATION
(MMSS-06-XX-X-XX.XX-X-K-XXX SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
* NOT RELEASED FOR PRODUCTION
.029 0.73 REF
.038 0.96 REF
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
FIG. 3
D
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
IPD1-XX-S-K
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
.100[2.54] SOCKET DISCREET CABLE ASSEMBLY
MMSS-XX-XX-X-XX.XX-X-X-XXX
05/03/2005
SHEET
2
OF
2
F:\DWG\MISC\MKTG\MMSS-XX-XX-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
DEAN P
京公网安备 11010802033920号
EEWORLD
