EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342E06B11B1MT5

Description
RESISTOR, THIN FILM, 0.15 W, 0.1 %, 25 ppm, 11100 ohm, SURFACE MOUNT, 0705, CHIP, GREEN
CategoryPassive components    The resistor   
File Size85KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342E06B11B1MT5 Overview

RESISTOR, THIN FILM, 0.15 W, 0.1 %, 25 ppm, 11100 ohm, SURFACE MOUNT, 0705, CHIP, GREEN

M55342E06B11B1MT5 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 0705
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length2.032 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.15 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance11100 Ω
Resistor typeFIXED RESISTOR
size code0805
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface Mount Chip
FEATURES
• Established reliability, “R” failure rate level
(100 ppm), C = 2
• High purity alumina substrate 99.6 % purity
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
• Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military/aerospace/QPL
Note
**
Please see document “Vishay Material Category Policy”:
www.vishay.com/doc?99902
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
• Specification changed by D.S.C.C. from MIL-R-55342 to
MIL-PRF-55342
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Passivated nichrome
10
to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
< - 25 dB
R
± 0.01 %
CONDITIONS
-
-
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
-
-
-
-
-
-
1 year at + 25 °C
COMPONENT RATINGS
CASE SIZE
POWER
RATING
(mW)
50
125
200
150
225
150
250
800
1000
500
50
100
WORKING
VOLTAGE
(V)
RESISTANCE RANGE () BY CHARACTERISTICS TOLERANCE
E
E
H, K, M
H, K, M
(0.1 %)
(1 %, 2 %, 5 %)
(0.1 %)
(1 %, 2 %, 5 %)
49.9 to 150K
49.9 to 150K
20 to 150K
20 to 150K
49.9 to 301K
49.9 to 301K
20 to 301K
20 to 301K
49.9 to 649K
49.9 to 649K
10 to 649K
10 to 649K
49.9 to 1.69M
49.9 to 1.69M
10 to 1.69M
10 to 1.69M
49.9 to 3.16M
49.9 to 3.16M
10 to 3.16M
10 to 3.16M
49.9 to 475K
49.9 to 475K
10 to 475K
10 to 475K
49.9 to 1.5M
49.9 to 1.5M
10 to 1.5M
10 to 1.5M
49.9 to 4.02M
49.9 to 4.02M
10 to 4.02M
10 to 4.02M
49.9 to 6.19M
49.9 to 6.19M
10 to 6.19M
10 to 6.19M
49.9 to 1M
49.9 to 1M
49.9 to 1M
49.9 to 1M
49.9 to 100K
49.9 to 100K
20 to 100K
20 to 100K
49.9 to 258K
49.9 to 261K
10 to 258K
10 to 261K
M55342/01
40
M55342/02
40
M55342/03
75
M55342/04
125
M55342/05
175
M55342/06
50
D55342/07
100
M55342/08
150
M55342/09
200
M55342/10
75
M55342/11
30
M55342/12
50
Note
• Values listed are a guide, refer to MIL spec for value/tolerance allowance
Revision: 08-Jun-11
1
Document Number: 60018
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
[nRF52840 DK Review] +52840 NFC (Part 2)
Burn the project in the nRF5_SDK_15.2.0_9412b96\examplesfcecord_text folder to 52840 and read it through NXP's pn532:The data of the NFC block is shown in the red line: Hello World![code]static ret_co...
lehuijie RF/Wirelessly
What domestic chips are needed to DIY a fast-charging chromium iron or an electric chromium iron that works as a laptop power supply?
I usually use the soldering station below to solder things. Sometimes, if I need to work outside, it is not convenient to carry such a large thing, so I will bring a 220V soldering iron. Some of the s...
littleshrimp Domestic Chip Exchange
Bluetooth module communicates with mobile phone
I have done an experiment on Zigbee communication, which requires communication between the Bluetooth module and the mobile phone Bluetooth module to receive RSSI. For a long time, the problem of garb...
Aguilera RF/Wirelessly
The compilation of the program sent by serial communication always fails
module UARTMYSELF (input CLOCK,RESET,output TXD,input iCall,output oDone,input [7:0]iData );parameter B115K2=9'd434;reg[3:0]i;reg[8:0]C1;reg[10:0]D1;reg rTXD;reg isDone;always@(posedge CLOCK or negedg...
星星brisk FPGA/CPLD
Does the clearance below the crystal oscillator refer to the layer where the chip is located or all layers?
RTRT Does the clearance below the crystal oscillator refer to the layer where the chip is located or all layers? Now I find that some designs only have clearance below the layer where the crystal osci...
se7ens Analog electronics
[Automatic clock-in walking timing system based on face recognition] Maixbit K210 initialization loading SD card unstable problem
I would like to ask friends who are participating in the competition and use K210, whether they have encountered the following problems: Problem 1: When K210 loads the SD card, it is unstable. Sometim...
alanlan86 DigiKey Technology Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号