EEWORLDEEWORLDEEWORLD

Part Number

Search

CFPO-SC-250S155.010.0MHZ

Description
OCXO, SINE OUTPUT, 10 MHz, HERMETIC SEALED, METAL LEADED PACKAGE-6
CategoryPassive components    oscillator   
File Size84KB,3 Pages
ManufacturerIQD Frequency Products
Download Datasheet Parametric View All

CFPO-SC-250S155.010.0MHZ Overview

OCXO, SINE OUTPUT, 10 MHz, HERMETIC SEALED, METAL LEADED PACKAGE-6

CFPO-SC-250S155.010.0MHZ Parametric

Parameter NameAttribute value
MakerIQD Frequency Products
package instructionHERMETIC SEALED, METAL LEADED PACKAGE-6
Reach Compliance Codecompliant
Ageing0.012 PPM/YEAR
Frequency Adjustment - MechanicalNO
frequency stability0.0002%
Frequency Stability - Voltage0.0001 ppm
input power1.8 W
Installation featuresTHROUGH HOLE MOUNT
offset frequency1 kHz
Nominal operating frequency10 MHz
Maximum operating temperature70 °C
Minimum operating temperature-20 °C
Oscillator typeSINE
Output impedance50 Ω
Output level0.5 V
Oven power supply voltage15V
phase noise-155 dBc/Hz
physical size50.8mm x 50.8mm x 25.0mm
Nominal supply voltage15 V
surface mountNO
Preheating power6 W
Maximum warm-up time10 Minute
CFPO-SC Series
(Hi-Reliable OCXO - Up to “Stratum 2” performance - No re-calibration over time)
ISSUE 1; 19 OCTOBER 2004
Output Compatibility
Sinewave +7dBm ±2dBm into 50Ω load (S)
Squarewave optional (C)
Description
The CFPO-SC series are a range of OCXO’s removing the need
for customers to re-calibrate their equipment over the
Harmonic Distortion
lifetime of operation
Harmonics
< -40dBc
Spurious
< -80dBc
Main performances are:-
Free-run stability range over lifetime operation from:
Phase Noise 10.0MHz typical (sinewave)
-8 (CFPO-SC1 for replacing Rubidium clocks)
1Hz
-100dBc/Hz
±1.6x10
10Hz
-130dBc/Hz
to ±1x10-7 (CFPO-SC4)
100Hz -145dBc/Hz
Holdover range over 24 hours operation:
1kHz
-155dBc/Hz
From 7µs over -20 to 70°C (CFPO-SC2) to 10µs with ±15°C
10kHz -158dBc/Hz
ambient change
Package Options (metal leaded package, hermetically sealed)
CFPO-SC-1 50.8 x 50.8 x 38.0mm (50B)
CFPO-SC-2 50.8 x 50.8 x 25.0mm (50)
CFPO-SC-3 51.0 X 41.0 X 25.0mm (51)
CFPO-SC-4 40.0 X 30.0 X 20.0mm (40)
Supply Options
Standard: 12V ±5% (12)
Optional: 15V (15)
Standard Frequencies
5.0, 8.192, 10.0, 10.24MHz
Frequency Range
5.0 to 15.0MHz
Higher frequencies may be available upon request
Initial tolerance @ 25°C Fo ±1x10
-8
Power Consumption (CFPO-SC1 / others)
Warm-up: <7.0W / 6.0W
@25°C: <2.5W / 1.8W (calm air)
Warm Up Time @ 25°C (typical)
±1x10
-8
after 15 mins (for CFPO-SC1)
±1x10
-8
after 10 mins (for others)
Environmental Specification (non-operating)
Storage temperature range -55 to 85°C
Shock - half-sine 50g 11ms / 3 per direction
IEC 68-2-27 Test Ea / Severity 50A
Vibration - 10g / 10-500Hz IEC 68-2-06 Test
Fc / Severity 500/10
Marking (printed label on top of can)
C-MAC or Customer’s Logo
Nominal Frequency (Fo) in MHz
Serial Number (1 letter & 5 numbers )
Date Code (4 digits for year and week)
Retrace after 24 Hours on / 24 Hours off @25°C
±2x10
-9
after 60 minutes
OCXOs
OCXOs
Frequency Adjustment
> ±5.0x10
-8
from 0V to reference voltage
EFC monotonic and positive slope (negative optional)
Oven Alarm “logic level” signal (optional) (A)
Logic “0” during warm-up time and if oven is not operating
Logic “1” when temperature regulation is operating
Reference Voltage Ouput (optional no reference voltage)
CFPO-SC-1 pkg 50B 8.0V±0.3V
CFPO-SC-2 pkg 50 8.2V±0.3V (options = 5V / 6.2V)
CFPO-SC-3 pkg 51 8.2V±0.3V (options = 5V / 6.2V)
CFPO-SC-4 pkg 40 8.0V±0.3V
Europe Tel: +44 (0)1460 270200
Americas Tel: +1 919 941 9333
Asia
Tel: +86 755 8826 5991
Fax: +44 (0)1460 72578
Fax: +1 919 941 9371
Fax: +86 755 8826 5990
Website: www.cmac.com
Method of flash programming in LPC2000 series microcontroller
Each VIC channel supports software interrupts and hardware interrupts, that is, each interrupt can be generated by software or hardware interrupts, and the software interrupt and the hardware interrup...
fish001 Microcontroller MCU
A Review of Low Power Design Technology
...
至芯科技FPGA大牛 FPGA/CPLD
Phase Shifter Switch Selection
I want to make a phase shifter and plan to use GaAs FET transistors. I would like to ask, if I use GaAs FET to make the phase shifter switch, is there any relationship between the phase shifter operat...
ZZH666 RF/Wirelessly
[Restored] Notice: Forum short message maintenance, will be restored tomorrow at noon
Some netizens may have discovered that the forum's short message function is temporarily unavailable. This is because the forum's short message function is currently undergoing maintenance and will be...
okhxyyo Suggestions & Announcements
What is the typical salary for a software engineer?
First of all, from the perspective of the entire market industry, software engineers and programmers belong to high-paying industries, and there is no doubt that they are supported by the state. The i...
huaqingyuanjian Integrated technical exchanges
[Dialogue with forum members] My main focus now is to find chips, buy them first and then develop them
Long time no see, have you all turned into buyers? Hahaha (This chat is all for activities, I am the administrator of reality) I chatted with Ding Ding, a senior engineer at the forum, in the afternoo...
nmg Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号