EEWORLDEEWORLDEEWORLD

Part Number

Search

SCP6G28-GL-AWE

Description
Fiber Optic Device,
CategoryWireless rf/communication    Optical fiber   
File Size449KB,18 Pages
ManufacturerSUMITOMO
Websitehttps://global-sei.com/
Download Datasheet Parametric Compare View All

SCP6G28-GL-AWE Overview

Fiber Optic Device,

SCP6G28-GL-AWE Parametric

Parameter NameAttribute value
MakerSUMITOMO
Reach Compliance Codeunknown

SCP6G28-GL-AWE Preview

Specification: TS-S08D026C
September, 2008
Technical specification
for
Small Form Factor Pluggable (SFP)
OC-48 (2488.32Mbps)
Sumitomo Part Number
SCP6G28-GL-# W E
SCP6G08-GL-# W E
Function
SR, 1310nm, 2km
IR-1, 1310nm, 15km
Sumitomo Electric reserves the right to make changes in this specification without prior notice.
Sumitomo Electric Industries, Ltd. and ExceLight Communications, Inc. have been granted license to the
following patents under a license agreement with Finisar corporation: US5,019,769, US6,439,918 B1
----------------------------------------------------------------------------
#Safety Precaution Symbols
This specification uses various picture symbols to prevent possible injury to operator or other persons or
damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols
before reading this specification.
!
Caution
Wrong operation without following this instruction may lead to human injury or property damage.
!
Warning
Wrong operation without following this instruction may lead to human death or serious injury.
Examples of picture symbols
!
indicates prohibition of actions. Action details are explained thereafter.
indicates compulsory actions or instructions. Action details are explained thereafter.
(SCP6G28/SCP6G08-GL)
1 / 18
Specification: TS-S08D026C
September, 2008
1
General
Features and applications of SCP6G28/SCP6G08 are listed below.
Features
* RoHS-6 Compliant.
* Compliant with SFP MSA.
* SFF-8472 rev.9 compliant diagnostic monitoring implemented.
* Power Supply Voltage
Single +3.3V
* Compact Package Size
57.5 X 13.9 X 8.6 mm
* Electrical Interface
AC coupled for DATA, LVTTL for Tx Disable and open collector output for
LOS and Tx Fault. Circuit ground is internally isolated from frame ground.
* Connector Interface
LC Duplex
* Serial ID Functionality
* Alarm and Warning Flags
* Bail type Actuator
2
Block diagram
SFP module
LD
Monitor
PD
TD+
Host board
Transmitter
Laser
Driver
100
TD-
Automatic
Power
Controller
10k
TxDisable
TxFault
4.7k
10k
Receiver
PD
RD+
Pre
Amplifier
Post
Amplifier
RD-
100
LOS
Temperature
Supply voltage
Tx bias current
Tx output power
Rx received power
4.7k
10k
EEPROM
Diagnostic monitor
EEPROM
150
MOD- DEF0
MOD- DEF1
MOD- DEF2
4.7k
10k
Figure 1.
Block diagram
!
Caution
Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur.
(SCP6G28/SCP6G08-GL)
2 / 18
Specification: TS-S08D026C
September, 2008
3
Package dimensions
Bail color is blue.
Note1 All Dimensions in mm
Note2 Dimensions with parentheses indicate the bail and latch release position
Figure 2.
Package dimensions
(SCP6G28/SCP6G08-GL)
3 / 18
Specification: TS-S08D026C
September, 2008
4
Pin assignment and function
VeeT
1
2
3
4
VeeT
TD-
TXFault
TD+
TX Disable
VeeT
MOD-DEF(2)
VccT
16
15
14
13
12
11
MOD-DEF(1)
VccR
6
7
8
9
10
MOD-DEF(0)
VeeR
NUC
RD+
LOS
RD-
VeeR
VeeR
VeeR
17
18
19
20
Towards
Bezel
5
Towards
ASIC
Figure 3.
Pin assignment
Pin number Name
Function
Plug sequence* Note
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
1
VeeT
Transmitter ground
2
TXFault
Transmitter fault indication
3
TXDisable
Transmitter disable input
4
MOD-DEF2 Module definition 2
5
MOD-DEF1 Module definition 1
6
MOD-DEF0 Module definition 0
7
NUC
No user connection
8
LOS
Loss of signal indication
9
VeeR
Receiver ground
10
VeeR
Receiver ground
11
VeeR
Receiver ground
12
RD-
Negative receiver Data out
13
RD+
Positive receiver Data out
14
VeeR
Receiver ground
15
VccR
Receiver power
16
VccT
Transmitter power
17
VeeT
Transmitter ground
18
TD+
Positive transmitter Data in
19
TD-
Negative transmitter Data in
20
VeeT
Transmitter ground
*Plug sequence: Pin engagement sequence during hot plugging.
Module disables on high or open
2 wire serial ID and interface
2 wire serial ID and interface
Grounded internally via 100ohm
Reserved for future use
TxFault
TxFault is an open collector output that shall be pulled up with a 4.7k to 10kohm resistor on the host
board. Pull up voltage is between 2.0V and VccT+0.3V. When high, output indicates a laser fault of
some kind. Low indicates normal operation. TxFault is asserted when bias current of laser exceeds the
factory-calibrated threshold level or when output power of transmitter degrades above/below the
factory-calibrated threshold level.
TxDisable
TxDisable is an input that is used to shut down the transmitter optical output. It is pulled up within the
module with a 4.7kohm resistor.
MOD-DEF
MOD-DEF 0, 1 and 2 are module definition pins. They should be pulled up with a 4.7k to 10kohm
resistor on the host board. The pull-up voltage shall be VccT. MOD-DEF0 indicates that the module is
present. MOD-DEF1 is the clock line of two wire serial interface for serial ID. MOD-DEF2 is the data
line of two wire serial interface for serial ID.
LOS
RD
LOS is an open collector output that shall be pulled up with a 4.7k to 10kohm resistor. Pull up voltage
between 2.0V and VccR+0.3V. Low indicates normal operation.
RD+/- are the differential receiver outputs. They are AC-coupled 100ohm differential lines that should
be terminated with 100ohm (differential) at the user’s SERDES. The AC coupling is done inside the
module and is thus not required on the host board.
TD+/- are the differential transmitter inputs. They are AC-coupled, differential lines with 100ohm
differential termination inside the module. The AC coupling is done inside the module and is thus not
required on the host board.
TD
(SCP6G28/SCP6G08-GL)
4 / 18
Specification: TS-S08D026C
September, 2008
Figure 4
SFP host board mechanical layout
Figure 5
Recommended bezel design
(SCP6G28/SCP6G08-GL)
5 / 18

SCP6G28-GL-AWE Related Products

SCP6G28-GL-AWE SCP6G08-GL-BWE SCP6G28-GL-BWE
Description Fiber Optic Device, Fiber Optic Device, Fiber Optic Device,
Maker SUMITOMO SUMITOMO SUMITOMO
Reach Compliance Code unknown unknown unknown
How to enable wireless triggering of devices via bootloading using a Bluetooth serial adapter
Bootloaders support field updates of product firmware. Bootloaders can update firmware using common communication interfaces such as UART, I2C, SPI, or USB, typically with a wired connection between t...
Jacktang Wireless Connectivity
USB TypeC training PPT materials from Tektronix Labs Open Day are here. Download for a limited time to get a gift (including training videos)
{:1_97:}[size=4]From now until April 13, download the USB training materials or recommended materials from Tektronix Labs Development Day and you will have a chance to win a 50-yuan JD card (35 copies...
EEWORLD社区 Test/Measurement
Power supply circuit guidance
The attached circuit has insufficient load capacity. When the output voltage exceeds 100ma, the output voltage drops seriously. Please give me some advice. In addition, the resistor R1 has been adjust...
yunshan_mc Analog electronics
LIS25BA can record, but there is "interference"
The operating voltage of LIS25BA is 1.8V. With so many development boards available, it is really difficult to find a 1.8V debugging board. Because we need to use TMD communication, the common microco...
littleshrimp MEMS sensors
TI chip strange labeling
Today I saw a chip CD4504, which is a TTL to COMS level chip. TI's chip is marked as CM504B, and the chip CD4051B I bought is marked as CM051B. It seems that CD4 has been replaced by CM. Haha, I almos...
bigbat Microcontroller MCU
Millions of 103 series MCU stocks are about to be released!!!
The imbalance between supply and demand in the global MCU market has become increasingly serious recently. After foreign MCU manufacturers successively announced price increase notices, domestic MCU m...
单片机0088 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号