EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7I2SC3682

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-7I2SC3682 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-7I2SC3682 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1550 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Why Qorvo is leading the new era of Wi-Fi connectivity? You will know after reading this.
Distributed Wi-Fi, also known as Wi-Fi mesh, is the next generation of indoor infrastructure for the Internet of Things (IoT). It is based on a "Pod in Every Room" architecture that provides seamless ...
alan000345 RF/Wirelessly
Software defines IoT chips, and technology integration promotes LPWAN2.0 ubiquitous IoT (Part 1)
As one of the important infrastructures of the digital industry, the Internet of Things has ushered in a golden period of development. Through the collection, analysis and output of data, the Internet...
zeta联盟 RF/Wirelessly
About the power factor of switching power supply and its correction method
[i=s]This post was last edited by qwqwqw2088 on 2021-11-3 13:28[/i]Switching power supply power factor and its correction methodPower factor compensation: In the 1950s, a method was proposed to improv...
qwqwqw2088 Power technology
EEWORLD University ---- RFID Training Series
RFID training series : https://training.eeworld.com.cn/course/4965...
wanglan123 RF/Wirelessly
How to use jumper caps in circuits
Now I have a serial port [color=#ff0000](1)[/color] and want to use an external jumper cap to select which part to connect to [color=#ff0000](2)[/color] or [color=#ff0000](3)[/color]. How should I des...
xxhhzz PCB Design
Calculate engine speed using the charging signal from the battery on a diesel engine
The engine speed is 1500 rpm, the AD sampling rate is 70K, and a total of 1024 points are collected. The time domain waveform is as follows:The red circle is the interference waveform, which has a lar...
Universe12 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号