Vin=270 V dc ±5%, Iout=20 A, CL=0 µF, free running (see Note 10) unless
otherwise specified
Technical Specification
Group A
Subgroup
(see Note 13)
ISOLATION CHARACTERISTICS
Isolation Voltage
Input RTN to Output RTN
Any Input Pin to Case
Any Output Pin to Case
Isolation Resistance (in rtn to out rtn)
Isolation Resistance (any pin to case)
Isolation Capacitance (in rtn to out rtn)
FEATURE CHARACTERISTICS
Switching Frequency (free running)
Synchronization Input
Frequency Range
Logic Level High
Logic Level Low
Duty Cycle
Synchronization Output
Pull Down Current
Duty Cycle
Enable Control (ENA1 and ENA2)
Off-State Voltage
Module Off Pulldown Current
On-State Voltage
Module On Pin Leakage Current
Pull-Up Voltage
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
Dielectric strength
500
500
500
100
100
44
500
500
2.0
-0.5
20
20
25
550
600
700
5.5
0.8
80
V
V
V
MΩ
MΩ
nF
kHz
kHz
V
V
%
mA
%
V
µA
V
µA
V
VSYNC OUT = 0.8 V
Output connected to SYNC IN of other MQFL unit
1
1
1
1
1
1
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
See Note 5
See Note 5
1, 2, 3
See Note 5
1, 2, 3
See Note 5
1, 2, 3
75
0.8
80
2
3.2
4.0
20
4.8
Current drain required to ensure module is off
Imax draw from pin allowed with module still on
See Figure A
2600
300
79
10
3
Hrs.
10
3
Hrs.
g
Electrical Characteristics Notes
1. Converter will undergo input over-voltage shutdown.
2. Derate output power to 50% of rated power at Tcase = 135ºC. 135ºC is above specified operating range.
3. High or low state of input voltage must persist for about 200µs to be acted on by the lockout or shutdown circuitry.
4. Current limit inception is defined as the point where the output voltage has dropped to 90% of its nominal value.
5. Parameter not tested but guaranteed to the limit specified.
6. Load current transition time ≥ 10 µs.
7. Settling time measured from start of transient to the point where the output voltage has returned to ±1% of its final value.
8. Line voltage transition time ≥ 250 µs.
9. Input voltage rise time ≥ 250 µs.
10. Operating the converter at a synchronization frequency above the free running frequency will slightly reduce the converter’s efficiency and may also cause
a slight reduction in the maximum output current/power available. For more information consult the factory.
11. After a disable or fault event, module is inhibited from restarting for 300 ms. See Shut Down section.
12. SHARE pin outputs a power failure warning pulse during a fault condition. See Current Share section.
13. Only the ES and HB grade products are tested at three temperatures. The C- grade products are tested at one temperature. Please refer to the ESS table
for details.
14. These derating curves apply for the ES and HB grade products. The C- grade product has a maximum case temperature of 70ºC and a maximum junction
temperature rise of 20ºC above TCASE.
15. Converter delivers current into a persisting short circuit for up to 1 second. See Current Limit in the Application Notes section.
16. The specified operating case temperature for ES grade products is -45ºC to 100ºC. The specified operating case temperature for C- grade products is 0ºC
to 70ºC.
Product# MQFL-270-06S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-005058 Rev. C
08/13/13
Page 4
MQFL-270-06S
Output:
6.0V
Current:
20A
Technical Figures
100
95
90
100
95
90
Efficiency (%)
80
75
70
65
60
0
4
Efficiency (%)
155 Vin
270 Vin
400 Vin
85
85
80
75
70
65
60
-55°C
155 Vin
270 Vin
400 Vin
Load Current (A)
8
12
16
20
-35°C
-15°C
5°C
Case Temperature (ºC)
25°C
45°C
65°C
85°C
105°C
125°C
Figure 1:
Efficiency at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at T
CASE
=25°C.
22
20
18
Figure 2:
Efficiency at nominal output voltage and 60% rated power vs.
case temperature for input voltage of 155V, 270V and 400V.
22
20
18
Power Dissipation (W)
14
12
10
8
6
4
2
0
0
4
8
12
16
155 Vin
270 Vin
400 Vin
Power Dissipation (W)
16
16
14
12
10
8
6
4
2
155 Vin
270 Vin
400 Vin
Load Current (A)
20
0
-55°C
-35°C
-15°C
5°C
Case Temperature (ºC)
25°C
45°C
65°C
85°C
105°C
125°C
Figure 3:
Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at Tcase=25°C.
32
28
24
20
192
168
144
Figure 4:
Power dissipation at nominal output voltage and 60% rated
power vs. case temperature for input voltage of 155V, 270V and 400V.
7
6
5
4
3
2
1
0
0
5
10
270 Vin
Iout (A)
16
12
8
4
0
25
45
65
85
105
125
135 145
Tjmax = 105ºC
Tjmax = 125ºC
Tjmax = 145ºC
96
72
48
24
0
Pout (W)
120
Output Voltage (V)
Case Temperature (ºC)
Load Current (A)
15
20
25
Figure 5:
Output Current / Output Power derating curve as a
function of Tcase and the Maximum desired power MOSFET junction
temperature (see Note 14). Vin = 270V
Product# MQFL-270-06S
Phone 1-888-567-9596
Figure 6:
Output voltage vs. load current showing typical current limit
curves. See Current Limit section in the Application Notes.
Generally speaking, when we hear PID, the first thing that comes to mind is the PID algorithm, Proportional, Integral, Differential. In fact, another commonly used explanation for PID is Photo Ionizat...
CC2541 and MSP430 communicate via serial port. The levels of CC2541 TX and MSP430 RX are reversed. The communication is not normal. How to solve this problem? I am connecting directly. Do I need to co...
In recent years, with the rapid development of China's economy, especially the blind investment and low-level expansion of some regions and high-energy-consuming industries, the contradiction of insuf...
NUCLEO-G431RB ReviewPlatform constructionI tried MDK514 before and found the same problem as http://bbs.21ic.com/icview-2861476-1-1.html?ordertype=1, so I downloaded the latest version of MDK528A dire...
introduction There are basically three IDEs for bare metal ARM program development: MDK or Keil, IAR, and ADS. ADS has stopped updating and is not recommended. I won't go into details about them here...[Details]
NXP, Tier 1s, OEMs and software ecosystem vendors can deploy virtualizer development kit 18 months before silicon is available Synopsys, Inc. (Nasdaq: SNPS) today announced the general availability...[Details]
As the new energy vehicle and energy storage markets continue to grow, global battery installed capacity will reach 1,202.6GWh in 2023 , a year-on-year increase of 38.6%. The growth in battery ins...[Details]
1. First of all, from the structural point of view, the fundamental difference between pulse radar level meter and guided wave radar level meter is that one is non-contact and the other is contact. T...[Details]
1. Overview
The power isolation sensor/transmitter is a small-volume, high-performance electrical signal measurement component or module developed for power detection (monitoring) in engineeri...[Details]
In fact, as long as you understand the characteristics of the triode, it will be much easier for you to use the microcontroller. Everyone actually knows that the triode has an amplifying effect, but ...[Details]
Power Subsystem for Photoplethysmography (PPG) Remote Patient Vital Signs Monitor - Part 1 Summary This two-part article describes a proven switch-mode power supply circuit design for remote pati...[Details]
stm32 HardFault_Handler debugging and problem finding method There are two main reasons why HardFault_Handler failure occurs in STM32: 1. Memory overflow or out-of-bounds access. This requires stand...[Details]
Hardware environment: STM32F105RCT6 Software environment: FreeRTOSV8 Problem description: The interrupt method is used to receive data, and then a frame of data is placed in the message queue. Th...[Details]
CAN bus is widely used in the control field. Nowadays, most CPU chips have extended CAN interface. This article focuses on the use of CAN bus based on STM32F103E series chips.
1. Hardware Basics
...[Details]
As a "social animal", I often ask myself soul-searching questions - why do the superheroes in the Avengers love their jobs so much and become more courageous as the battle goes on when faced with all...[Details]
I. Overview Temperature is one of the most basic environmental parameters. It is closely related to people's lives and industrial and agricultural production. Temperature measurement is indispensab...[Details]
In recent years, industrial measurement and control systems have shifted from traditional centralized measurement and control systems to networked distributed control systems. With the rapid developme...[Details]
According to Appleinsider, in a recent research report, Samik Chatterjee, chief analyst at JPMorgan Chase, pointed out that compared with last year's Apple iPhone 12 series models, the delivery time ...[Details]
0 Introduction
The traditional digital filter hardware is mainly realized by using application-specific integrated circuits (ASIC) and digital signal processors (DSP). The SRAM lookup tabl...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
