IS41LV16257B
256K x 16 (4-MBIT) DYNAMIC RAM
WITH FAST PAGE MODE
DESCRIPTION
The
ISSI
IS41LV16257B is 262,144 x 16-bit high-
performance CMOS Dynamic Random Access
Memories. Fast Page Mode allows 512 random
accesses within a single row with access cycle time as
short as 12 ns per 16-bit word. The Byte Write control,
of upper and lower byte, makes these devices ideal for
use in 16- and 32-bit wide data bus systems.
These features make the IS41LV16257B ideally suited
for high band-width graphics, digital signal processing,
high-performance computing systems, and peripheral
applications.
The IS41LV16257B is packaged in a 40-pin, 400-mil
SOJ and TSOP (Type II).
JUNE 2007
FEATURES
•
•
•
•
•
•
•
•
Fast access and cycle time
TTL compatible inputs and outputs
Refresh Interval: 512 cycles/8 ms
Refresh Mode:
RAS-Only, CAS-before-RAS
(CBR), and Hidden
JEDEC standard pinout
Single power supply: 3.3V ± 10%
Byte Write and Byte Read operation via
two
CAS
Lead-free available
KEY TIMING PARAMETERS
Parameter
Max.
RAS
Access Time (t
RAC
)
Max.
CAS
Access Time (t
CAC
)
Max. Column Address Access Time (t
AA
)
Min. Fast Page Mode Cycle Time (t
PC
)
Min. Read/Write Cycle Time (t
RC
)
-35
35
11
18
14
60
-60
60
15
30
25
110
Unit
ns
ns
ns
ns
ns
Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time
without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc.
Rev. C
06/18/07
1
IS41LV16257B
FUNCTIONAL DESCRIPTION
The IS41LV16257B is a CMOS DRAM optimized for high-
speed bandwidth, low-power applications. During READ or
WRITE cycles, each bit is uniquely addressed through the
18 address bits. These are entered nine bits (A0-A8) at a
time. The row address is latched by the Row Address Strobe
(RAS). The column address is latched by the Column
Address Strobe (CAS).
RAS
is used to latch the first nine bits
and
CAS
is used to latch the latter nine bits.
The IS41LV16257B has two
CAS
controls,
LCAS
and
UCAS.
The
LCAS
and
UCAS
inputs internally generate a
CAS
signal functioning in an identical manner to the single
CAS
input on the other 256K x 16 DRAMs. The key difference
is that each
CAS
controls its corresponding I/O tristate logic
(in conjunction with
OE
and
WE
and
RAS). LCAS
controls
I/O0 - I/O7 and
UCAS
controls I/O8 - I/O15.
The IS41LV16257B
CAS
function is determined by the first
CAS
(LCAS or
UCAS)
transitioning LOW and the last
transitioning back HIGH. The two
CAS
controls give the
IS41LV16257B both BYTE READ and BYTE WRITE cycle
capabilities.
Write Cycle
A write cycle is initiated by the falling edge of
CAS
and
WE,
whichever occurs last. The input data must be valid at or
before the falling edge of
CAS
or
WE,
whichever occurs last.
Refresh Cycle
To retain data, 512 refresh cycles are required in each
8 ms period. There are two ways to refresh the memory:
1. By clocking each of the 512 row addresses (A0 through
A8) with
RAS
at least once every 8 ms. Any read, write,
read-modify-write or
RAS-only
cycle refreshes the ad-
dressed row.
2. Using a
CAS-before-RAS
refresh cycle.
CAS-before-
RAS
refresh is activated by the falling edge of
RAS,
while
holding
CAS
LOW. In
CAS-before-RAS
refresh cycle, an
internal 9-bit counter provides the row addresses and the
external address inputs are ignored.
CAS-before-RAS
is a refresh-only mode and no data access
or device selection is allowed. Thus, the output remains in
the High-Z state during the cycle.
Memory Cycle
A memory cycle is initiated by bringing
RAS
LOW and it is
terminated by returning both
RAS
and
CAS
HIGH. To
ensure proper device operation and data integrity any
memory cycle, once initiated, must not be ended or aborted
before the minimum t
RAS
time has expired. A new cycle
must not be initiated until the minimum precharge time t
RP
,
t
CP
has elapsed.
Power-On
After application of the V
DD
supply, an initial pause of
200 µs is required followed by a minimum of eight initialization
cycles (any combination of cycles containing a
RAS
signal).
During power-on, it is recommended that
RAS
track with V
DD
or be held at a valid V
IH
to avoid current surges.
Read Cycle
A read cycle is initiated by the falling edge of
CAS
or
OE,
whichever occurs last, while holding
WE
HIGH. The column
address must be held for a minimum time specified by t
AR
.
Data Out becomes valid only when t
RAC
, t
AA
, t
CAC
and t
OEA
are all satisfied. As a result, the access time is dependent
on the timing relationships between these parameters.
4
Integrated Silicon Solution, Inc.
Rev. C
06/18/07
IS41LV16257B
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
T
V
DD
I
OUT
P
D
T
A
T
STG
Parameters
Voltage on Any Pin Relative to GND
Supply Voltage
Output Current
Power Dissipation
Operation Temperature
Storage Temperature
3.3V
3.3V
Rating
–0.5 t0 +4.6
–0.5 t0 +4.6
50
1
0 to +70
-40 to +85
–55 to +125
Unit
V
V
mA
W
°C
°C
Com.
Ind.
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause perma-
nent damage to the device. This is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
RECOMMENDED OPERATING CONDITIONS
(Voltages are referenced to GND)
Symbol
V
DD
V
IH
V
IL
T
A
Parameter
Supply Voltage
Input High Voltage
Input Low Voltage
Ambient Temperature
Voltage
3.3V
3.3V
3.3
Com.
Ind.
Min.
3.0
2.0
–0.3
0
-40
Typ.
3.3
—
—
—
—
Max.
3.6
V
DD
+ 0.3
0.8
70
85
Unit
V
V
V
°C
CAPACITANCE
(1,2)
Symbol
C
IN
1
C
IN
2
C
IO
Parameter
Input Capacitance: A0-A8
Input Capacitance:
RAS, UCAS, LCAS, WE, OE
Data Input/Output Capacitance: I/O0-I/O15
Max.
5
7
7
Unit
pF
pF
pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: T
A
= 25°C, f = 1 MHz, V
DD
=3.3V ± 10%.
Integrated Silicon Solution, Inc.
Rev. C
06/18/07
5