The ASM3P2759A uses the most efficient and optimized
modulation
profile
approved
by
the
FCC
and
is
implemented by using a proprietary all digital method.
The ASM3P2759A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Applications
The ASM3P2759A is targeted towards all portable devices
with very low power requirements like MP3 players and
digital still cameras.
Product Description
The ASM3P2759A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2759A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
dependent signals. The ASM3P2759A allows significant
system cost savings by reducing the number of circuit
board layers ferrite beads, shielding that are traditionally
required to pass EMI regulations.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
VDD = 3.3V / 2.5V
200pS (Max)
45/55%
F
IN
/128
±1% @ 3MHz
Block Diagram
VDD
PD
XIN
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
Modulation
PLL
XOUT
Phase
Detector
Loop
Filter
VCO
Output
Divider
ModOUT
VSS
Alliance Semiconductor
2575 Augustine Drive
•
Santa Clara, CA
•
Tel: 408.855.4900
•
Fax: 408.855.4999
•
www.alsc.com
Notice: The information in this document is subject to change without notice.
September 2005
rev 1.6
Pin Configuration (6-pin TSOT- 23 Package)
ASM3P2759A
PD
1
XOUT
2
XIN/CLKIN
3
6
VSS
ModOUT
VDD
ASM3P2759A
5
4
Pin Description
Pin#
1
2
3
4
5
6
Pin Name
PD
XOUT
XIN/CLKIN
VDD
ModOUT
VSS
Type
I
O
I
P
O
P
Description
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
Crystal connection. If using an external reference, this pin must be left unconnected.
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Power supply for the entire chip
Spread spectrum clock output.
Ground connection.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
September 2005
rev 1.6
Pin Configuration (8-pin SOIC and TSSOP Packages)
ASM3P2759A
XIN/CLKIN
1
XOUT
2
PD
3
NC
4
8
7
6
5
VDD
NC
ModOUT
VSS
ASM3P2759A
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN/CLKIN
XOUT
PD
NC
VSS
ModOUT
NC
VDD
Type
I
O
I
-
P
O
-
P
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
No connect.
Ground connection.
Spread spectrum clock output.
No connect.
Power supply for the entire chip
Modulation Profile
Specification
Description
Frequency Range
For 2.5V Supply
For 3.3V Supply
Specification
3MHz < CLKIN < 5MHz
3MHz < CLKIN < 6MHz
F
IN
/128
±1% @ 3MHz
Modulation Equation
Frequency Deviation
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
September 2005
rev 1.6
Absolute Maximum Ratings
Symbol
VDD, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
ASM3P2759A
Parameter
Rating
-0.5 to +7.0
-65 to +125
0 to 70
260
150
2
Unit
V
°C
°C
°C
°C
KV
Voltage on any pin with respect to Ground
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
VDD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
VSS - 0.3
2.0
-
-
-
-
-
1.8
-
-
2.375
-
-
Typ
-
-
-
-
3
3
-
-
-
2.0
2.5
-
50
Max
0.8
VDD + 0.3
-35
35
-
-
0.6
-
10
-
2.625
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.5V, VDD=2.5V)
XOUT output high current (@1.8V, VDD=2.5V)
Output low voltage (VDD = 2.5 V, I
OL
= 8mA)
Output high voltage (VDD = 2.5 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (2.5V, 3MHz and with no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN/CLKIN and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 3MHz
Input Frequency = 5MHz
Parameter
Min
3
3
-
-
0.5
0.4
-
45
Typ
-
-
±1
±0.6
1.0
0.9
-
50
Max
5
5
-
-
1.2
1.1
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.7V to 1.7V)
Output fall time (measured from 1.7V to 0.7V)
Jitter (cycle to cycle)
Output duty cycle
* t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
September 2005
rev 1.6
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+ 25°C) unless otherwise stated)
ASM3P2759A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
VDD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
VSS - 0.3
2.0
-
-
-
-
-
2.5
-
-
2.7
-
-
Typ
-
-
-
-
3
3
-
-
2.5
3.3
-
45
Max
0.8
VDD + 0.3
-35
35
-
-
0.4
-
10
-
3.6
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.4V, VDD=3.3V)
XOUT output high current (@2.5V, VDD=3.3V)
Output low voltage (VDD = 3.3 V, I
OL
= 8mA)
Output high voltage (VDD = 3.3 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (3.3V, 3MHz and with no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN/CLKIN and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable; PD pin is made high from low.
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency
Deviation
Input Frequency = 3MHz
Input Frequency = 6MHz
Parameter
Min
3
3
-
-
0.4
0.4
-
45
Typ
-
-
±1
±0.55
1.0
0.9
-
50
Max
6
6
-
-
1.2
1.0
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.8 to 2.0V)
Output fall time (measured at 2.0V to 0.8V)
Jitter (cycle to cycle)
Output duty cycle
*t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
[i=s]This post was last edited by Beifang on 2018-12-28 22:48[/i] 1. Using NXP Rapid IoT APP is also very similar to IDE. From the design point of view, data management is not included, but it provide...
The USB interface design scheme based on DSP is described from the aspects of interface hardware design, interface operation principle, software design process and interrupt service program design poi...
In microwave communication systems, there is a third-order intermodulation intercept point OPI3 (third-order intercept point), which is an important indicator for measuring the linearity and distortio...
USB device request command: bmRequestType + bRequest + wValue + wIndex + wLengthNumber Value Name(0) 0 GET_STATUS: used to return the status of a specific receiver(1) 1 CLEAR_FEATURE: used to clear or...
Big guys, I need help from a newbieQuestion 1: I know how to use an oscilloscope, but I don’t know whether the waveform measured by the oscilloscope is correct or wrong, and how to judge whether the w...
Summary This article describes how to use a ready-to-use platform to accelerate development and efficiently design standards-compliant power quality (PQ) measurement instruments. The article explor...[Details]
Charging time is a major consideration for consumers and businesses evaluating the purchase of electric vehicles (EVs). To reduce charging time, the industry is turning to direct current chargers (...[Details]
A single-chip microcomputer emulator is a set of dedicated hardware devices designed and manufactured for the purpose of debugging single-chip microcomputer software.
The architecture of a sin...[Details]
Common faults of CNC system
According to the structure, working principle and characteristics of the CNC system, and in conjunction with our experience in repair, the common fault locations an...[Details]
A few days ago, SmartisanOS, created by Luo Yonghao, officially released an "Announcement on the Offline of the Smartisan Forum" on Weibo, stating that the Smartisan Forum will cease services ...[Details]
1. For example, the variable i is defined in the function. i is a local variable and is stored in the memory stack. When checking the variable during simulation, the problem of "not in scope" will ap...[Details]
According to reports, the European Space Agency (ESA) has commissioned the Swiss startup "ClearSpace" to submit a plan to launch a "scavenger" in 2025 to clean up a 100-kilogram piece of debris in ES...[Details]
China Energy Storage Network News:
(Li Jiangning, Chang Bingyu, Lu Guoqiang) China State Grid Qinghai Electric Power Company announced on the 12th that on the 11th, the world's largest-scal...[Details]
Recently, Qorvo and Active-Semi held a press conference in Beijing. This was also the first appearance of Active Semi after being acquired by Qorvo. Larry Blackledge, general manager of Qorvo's progr...[Details]
“We try to separate the concepts of the two revolutions, autonomous driving and assistance, and the revolution of saving lives can be achieved through the development of ADAS technology.” Mobileye ...[Details]
On July 22, China Southern Power Grid Digital Power Grid Research Institute Co., Ltd. (hereinafter referred to as "China Southern Power Grid Digital Power Grid Research Institute") was established ...[Details]
Today, the new energy vehicle industry is booming, and safety management and testing are strictly controlled in all production links. What kind of detection effect can Keyence microscopes achieve f...[Details]
On November 24, Huawei announced the launch of OceanStor Dorado 2100, the industry's first Active-Active architecture NAS storage for small and medium-sized enterprises. According to reports, OceanSt...[Details]
Guangzhou, October 18, 2024 /PRNewswire/ -- On October 17, at the new product and service launch event of the 136th China Import and Export Fair (also known as the "Canton Fair"), SGS, an internati...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
