E1SLA10-20.000MTR datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> E1SLA10-20.000MTR

E1SLA10-20.000MTR: DescriptionQUARTZ CRYSTAL RESONATOR, 20MHz, ROHS COMPLIANT, RESISTANCE WELD PACKAGE-2; CategoryPassive components Crystal/resonator; File Size128KB，2 Pages; ManufacturerECLIPTEK; Websitehttp://www.ecliptek.com; Environmental Compliance

Download Datasheet Parametric View All

E1SLA10-20.000MTR Overview

QUARTZ CRYSTAL RESONATOR, 20MHz, ROHS COMPLIANT, RESISTANCE WELD PACKAGE-2

E1SLA10-20.000MTR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	ECLIPTEK
package instruction	ROHS COMPLIANT, RESISTANCE WELD PACKAGE-2
Reach Compliance Code	compliant
Other features	AT-CUT CRYSTAL; TAPE AND REEL
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	1000 µW
frequency stability	0.002%
frequency tolerance	15 ppm
JESD-609 code	e3
load capacitance	10 pF
Manufacturer's serial number	E1S
Installation features	SURFACE MOUNT
Nominal operating frequency	20 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
physical size	L13.3XB4.85XH3.2 (mm)/L0.524XB0.191XH0.126 (inch)
Series resistance	50 Ω
surface mount	YES
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrier

Preview

Download Datasheet

View All

E1S

Series

• RoHS Compliant (Pb-Free)

• HC-49/UP short package

• AT or BT cut available

• Resistance weld seal

• Tight tolerance/stability

• Tape and reel available

NOTES

E1S

H 3.20

L 13.30

W 4.85

CRYSTAL

_____________________________________________________________________________________________________________________________________________________________________________________________

ELECTRICAL SPECIFICATIONS

Frequency Range

Frequency Tolerance / Stability

Over Operating Temperature Range

Operating Temperature Range

Aging (at 25°C)

Storage Temperature Range

Shunt Capacitance

Insulation Resistance

Drive Level

Load Capacitance (C

)

3.579545MHz to 50.000MHz

±50ppm / ±100ppm (Standard), ±30ppm / ±50ppm (AT cut only), ±15ppm / ±30ppm (AT cut only),

±15ppm / ±20ppm (AT cut only), or ±10ppm / ±15ppm (AT cut only)

0°C to 70°C, -20°C to 70°C (AT cut only), or -40°C to 85°C (AT cut only)

±5ppm / year Maximum

-40°C to 125°C

7pF Maximum

500 Megaohms Minimum at 100V

1 mWatt Maximum

18pF Parallel Resonant (Standard), Custom C

≥10pF

Parallel Resonant, or Series Resonant

EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION (MODE), AND CUT

Frequency Range

3.579545MHz to 4.999MHz

5.000MHz to 5.999MHz

6.000MHz to 7.999MHz

8.000MHz to 8.999MHz

9.000MHz to 9.999MHz

10.000MHz to 14.999MHz

MANUFACTURER

ESR (Ω)

200 Max

150 Max

120 Max

90 Max

80 Max

70 Max

Recommended Resources

Constant current source circuit composed of MIC29152 and dual operational amplifiers

Internal circuit of STK3048 and 6153

Single line in and out delay switch circuit

Test probe circuit

Motor automatic restart circuit

Rice cooker circuit diagram 04

CircuitPython OLED Watch/Bracelet: From: https://learn.adafruit.com/circuitpython-oled-watch...; dcexpert MicroPython Open Source section

In-depth Study on Photorelay TLP3547F: [i=s]This post was last edited by anger0925 on 2018-9-12 18:02[/i] [align=left][font=宋体]I was fortunate to apply for Toshiba's photorelay evaluation board to experience it, so I will first learn about...; anger0925 Toshiba Photorelays TLP3547 Review

FAQ_ S2LP FEC Rules: Author: Joshua Zhu, ST engineer Click to download the pdf document:Keywords: S2-LP, sub 1GHZProblem: Customers use S2-lp to develop their products. Now they can enable FEC to communicate between two S...; nmg ST - Low Power RF

The difference between POR and PUC in MSP430 MCU: [size=4]What is the difference between the POR signal and the PUC signal in the MSP430F149 microcontroller? What operations does the microcontroller perform after detecting these two signals? Thank yo...; Aguilera Microcontroller MCU

Floating-point C2000 chip calculation skills and points for attention: [size=4]The precision of floating point numbers is determined by the number of digits in the mantissa. Most numbers will have errors when expressed as floating point numbers. These errors are small an...; 灞波儿奔 DSP and ARM Processors

DSP6678 NDK network configuration (UDP) points: 1. If you want to use NDK, the CCS project you create must be a project that runs sys/bios.2. If you want to see the network demo of 6678, the demo path is: C:\ti\mcsdk_2_01_02_06\examplesdk\helloWorl...; fish001 DSP and ARM Processors

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components