EEWORLDEEWORLDEEWORLD

Part Number

Search

7044WWTH2RCDBX653U622-U1022

Description
Rocker Switch, DP3T, Latched, 0.02A, 20VDC, Solder Terminal, Medium Rocker Actuator, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size567KB,14 Pages
ManufacturerAPEM
Environmental Compliance  
Download Datasheet Parametric View All

7044WWTH2RCDBX653U622-U1022 Overview

Rocker Switch, DP3T, Latched, 0.02A, 20VDC, Solder Terminal, Medium Rocker Actuator, Through Hole-right Angle

7044WWTH2RCDBX653U622-U1022 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeMEDIUM ROCKER
body width12 mm
body height13.2 mm
Body length or diameter16.8 mm
Contact (AC) maximum rated R load.02A@20VAC
Maximum contact current (AC)0.02 A
Maximum contact current (DC)0.02 A
Contact (DC) maximum rated R load.02A@20VDC
Maximum contact voltage (AC)20 V
Maximum contact voltage (DC)20 V
Electrical life50000 Cycle(s)
Manufacturer's serial number7000
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED
switch functionDP3T
Switch typeROCKER SWITCH
Termination typeSOLDER
7000 series
Rocker and paddle switches
Distinctive features and specifications
Wide variety of actuators
Many mounting styles for panel or PCB
VDE, UL and CSA approved
ELECTRICAL SPECIFICATIONS
• Current/voltage rating with resistive load :
Contact
Silver A
Silver,
gold plated AD
Brass,
gold plated CD
Maximum
3A 250VAC - 6A 125VAC - 4A 30VDC
3A 250VAC - 6A 125 VAC - 4A 30VDC
Gold plating withstands up to 100mA 30VDC.
0,4 VA at 20VAC or DC
Minimum
50mA 10VDC
10mA 50mV
10µA 5V
10mA 50mV
10µA 5V
Level *
III and IV
I to IV
I and II
D
• For inductive, lamp or capacitive loads, consult factory.
• Initial contact resistance : 10 mΩ
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
1.500 Vrms 50 Hz min. between poles
1.500 Vrms 50 Hz min. between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life : 50.000 cycles at full load
* For details, see technical information, end of catalogue.
MATERIALS
GENERAL SPECIFICATIONS
• Case : diallylphthalate (DAP) or
high temperature plastic material
(UL94-V0)
• Actuator : polyamide
• Housing : stainless steel or steel
tin plated
• Bracket : steel, tin plated
• Contacts
A
: silver
AD
: silver, gold plated
CD
: brass, gold plated
• Terminal seal : epoxy
• Mechanical life : 100.000 cycles
• Panel thickness : 1 (.039) to 2,5 mm(.098)
• Operating temperature : -40°C to +85°C
AGENCY APPROVALS
EN 61058-1
For VDE, refer to 57000 series.
Availability
: consult factory for details of approved models.
Marking
: to order switches marked UL or CSA, complete appropriate box of
ordering format.
APEM
www.apem.com
D-23
[Bluesun AB32VG1 RISC-V evaluation board] IDE installation and use
[i=s]This post was last edited by Beifang on 2021-8-9 14:03[/i]1. This board is perfectly compatible with rtthread studio. Follow the manual first, click multiple pictures, and click next. First downl...
北方 Domestic Chip Exchange
【DIY Creative LED】Add touch button and install it on LED lamp
[i=s]This post was last edited by dcexpert on 2020-10-3 17:59[/i]The effect after installing the touch spring and fixing it with hot melt glue. When applying glue, use a USB cable to assist to avoid a...
dcexpert MCU
Know a little about the AD sampling single mode of dsp28335
Three modes are configured: single mode, continuous mode and DMA transfer. Single mode calls the acquisition function once to collect data at a specified AD port, and samples when needed. Continuous m...
fish001 DSP and ARM Processors
[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy
[i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...
MianQi Domestic Chip Exchange
SensorTile.box uses air pressure sensors to analyze environmental changes
After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...
littleshrimp MEMS sensors
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号