MD06S2NCQD datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> MD06S2NCQD

MD06S2NCQD: DescriptionRotary Switch, 6 Positions, DP6T, Latched, 0.25A, 28VDC, Solder Terminal, Flush, Screwdriver Slot Actuator, Through Hole-straight, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size405KB，6 Pages; ManufacturerITT; Websitehttp://www.ittcannon.com/; Environmental Compliance

Download Datasheet Parametric View All

MD06S2NCQD Overview

Rotary Switch, 6 Positions, DP6T, Latched, 0.25A, 28VDC, Solder Terminal, Flush, Screwdriver Slot Actuator, Through Hole-straight, ROHS COMPLIANT

MD06S2NCQD Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator type	FLUSH, SCREWDRIVER SLOT
body height	9.4 mm
Body length or diameter	13.34 mm
Contact (AC) maximum rated R load	.25A@125VAC
Maximum contact current (AC)	0.25 A
Maximum contact current (DC)	0.25 A
Contact (DC) maximum rated R load	.25A@28VDC
Maximum contact voltage (AC)	125 V
Maximum contact voltage (DC)	28 V
Electrical life	10000 Cycle(s)
Graduation angle	30 deg
JESD-609 code	e4
Manufacturer's serial number	MD06
Installation features	THROUGH HOLE-STRAIGHT
Number of positions	6
Number of switching segments	1
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
surface mount	NO
Switch action	LATCHED
switch function	DP6T
Switch type	ROTARY SWITCH
Terminal surface	Silver (Ag)
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

C&K M Series

Half-inch Rotary Switches

Features/Benefits

•

Multi-pole and multi-positions

•

Panel and PCB mounting

•

Stainless steel actuator

•

Non-shorting contacts

Typical Applications

•

Test equipment

•

Industrial equipment

•

Medical equipment

Models Available

Specifications

CONTACT RATING: Q contact material: Carry-6 AMPS continuous.

Switch-250 mA max. @ 125 V AC or 28 DC. Non-shorting

contacts standard. See page L-15 for additional ratings.

ELECTRICAL LIFE: 10,000 make-and-break cycles at 150 mA,

125 V AC or 28 DC.

CONTACT RESISTANCE: Below 20 mΩ typ. initial @

2-4 V DC, 100 mA, for both silver and gold plated contacts.

INSULATION RESISTANCE: 1010

Ω

min.

DIELECTRIC STRENGTH: 600 Vrms min. @ sea level.

OPERATING & STORAGE TEMPERATURE: –30ºC to 85ºC.

OPERATING TORQUE: 4-7 ounces-inches typ. initial.

SOLDERABILITY: Per MIL-STD-202F method 208D, or

EIA RS-186E method 9 (1 hour steam aging).

NOTE:

Any models supplied with Q or G contact material are RoHS compliant. For the

latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs.

NOTE:

Specifications and materials listed above are for switches with standard options.

For information on specific and custom switches, consult Customer Service Center.

Materials

HOUSING AND BUSHING: Zinc alloy, bright zinc plated,

with clear chromate finish.

ACTUATOR: Zinc alloy, nickel plated or stainless steel.

BASE: Diallylphthalate (DAP) or melamine phenolic, with insert

molded terminals.

ROTOR: Glass filled polyester (UL 94V-0).

MOVABLE CONTACTS:

Non-shorting: Q contact material: Copper alloy, silver plated.

See page L-15 for additional contact materials.

STATIONARY CONTACT & ALL TERMINALS: Q contact material:

Copper alloy, silver plated. All terminals insert molded. All

terminals present regardless of number of switch positions.

See page L-15 for additional contact materials.

CONTACT SPRING: Music wire, phosphate coated.

STOP PIN: Stainless steel.

STOP RING: Brass.

HARDWARE: Nut: Brass, nickel plated; Lockwasher: Steel,

nickel plated.

Rotary

Build-A-Switch

To order, simply select desired option from each category and place in the appropriate box. Available options are shown and

described on pages L-13 thru L-17. For additional options not shown in catalog, consult Customer Service Center.

Switch Function

MA00

SP, 10 pos., 36°

MA02

SP, 2 pos., 36°

MA03

SP, 3 pos., 36°

MA04

SP, 4 pos., 36°

MA05

SP, 5 pos., 36°

MA06

SP, 6 pos., 36°

MA10

SP, 10 pos., 36°

MB00

DP, 5 pos., 36°

MB03

DP, 3 pos., 36°

MB04

DP, 4 pos., 36°

MB05

DP, 5 pos., 36°

MC00

SP, 12 pos., 30°

MC03

SP, 3 pos., 30°

MC07

SP, 7 pos., 30°

MC12

SP, 12 pos., 30°

MD00

DP, 6 pos., 30°

MD06

DP, 6 pos., 30°

ME00

SP, 10 pos., 36°

ME04

SP, 4 pos., 36°

MF00

DP, 5 pos., 36°

MG00

SP, 12 pos., 30°

MH00

DP, 6 pos., 30°

Actuator & Bushing

.650"

long, flatted

Screwdriver slot, flush

.650" long, round

.650" long, flatted

Screwdriver slot, flush

.650" long, round

.785" long, slot

Short/Non-short

Non-shorting contacts

Terminations

Solder lug

PC Thru-hole

Contact Material

Silver

Gold over silver

Seal

No seal

Splashproof shaft & panel seal

Dimensions are shown: Inch (mm)

Specifications and dimensions subject to change

L–12

www.ittcannon.com

C&K M Series

Half-inch Rotary Switches

SEAL

NO EPOXY SEAL

SPLASHPROOF SHAFT AND PANEL SEAL

Setting Stops With Stop Pins

MA00, MB00, MC00 & MD00 Models Only:

The number of switch positions or stops are adjustable by means of stop pins provided with each switch. Switches are normally

shipped with stop pins and hardware in bulk, not installed. Without stop pins, switches have full 360º rotation and no stops.

Note that all two pole models begin to repeat when actuated 180º or more.

To set stops, refer to figures 1 & 2. Orient switch so that terminal no. 1 is as shown. Turn actuator to position 1, using flats on

bushing and terminal no. 1 as reference. Install CCW stop pin in hole designated ‘X’. Install second stop pin in hole number

corresponding to the number of positions desired. Note that two pole models will begin to repeat when actuated 180º or more.

To retain stop pins, use adhesive mylar washer included; see figure 3.

All models except MX00 models have number of switch positions or stops pre-set at factory and are not adjustable.

Hardware:

Two stop pins, mounting nut, and lockwasher supplied standard.

P/N 537100000

Rotary

36º Indexing Models

Top View

Fig. 1

30º Indexing Models

Top View

Fig. 2

Fig. 3

P/N 537202000

Setting Stops With Stop Rings

ME00, MF00, MG00 & MH00 Models Only:

The number of switch positions or stops are adjustable by means of stop rings provided with each switch. These models are

normally shipped with stop rings and hardware in bulk, not installed. Without stop rings, switches have full 360º rotation and no

stops. Note that all two pole models begin to repeat when actuated 180º or more.

To set stops refer to figures 4 & 5. Orient switch so that terminal no. 1 is as shown. Turn actuator to pos. 1 using flats on bushing

and terminal no. 1 as reference. See figure 6 and install inner stop ring with short tab in hole designated ‘X’. Install outer

stop ring with long tab in hole number corresponding to the number of positions desired. Note that all two pole models begin to

repeat when actuated 180º or more. Use mounting nut and lockwasher to retain stop rings.

All MEXX, MFXX, MGXX & MHXX Models (Except MX00 models):

Number of switch positions or stops are preset at factory, but are user adjustable.

Hardware:

Two stop rings, mounting nut and lockwasher supplied standard.

36º Indexing Models

Top View

Fig. 4

30º Indexing Models

Top View

Fig. 5

Fig. 6

Dimensions are shown: Inch (mm)

Specifications and dimensions subject to change

L–16

www.ittcannon.com

Recommended Resources

Lesound controlled running water lamp circuit

STK4152II audio IC circuit diagram

Universal battery charger circuit (2)

Electronic combination lock 2

Computer motherboard circuit diagram 810 3_17

Computer motherboard circuit diagram 820 1_56

Single chip digital stopwatch program: I made a stopwatch program for students to refer to. We have covered all the knowledge points involved in the program, including timers, digital tubes, interrupts, buttons, and other knowledge points....; Aguilera Microcontroller MCU

Did you feel disappointed after watching Avengers 4?: Although 40 Oceans was produced by someone else, I don’t think it’s that good. For example, Captain Marvel, I don’t know what the ending is, which makes me feel inexplicable....; EricGo Talking

Problem with the serial port receiving data of stm32?: Is the HAL_UART_RxCpltCallback(huart) function of stm32 outside or inside the interrupt? I want to put the serial port receiving data into freeRTOS. If it is inside the interrupt, I need to use the xQ...; bigbat stm32/stm8

TVP5150 video decoding chip debugging summary: Development platform: TI DM365 multimedia processor, TVP5150 video decoding chip Development requirements: Use TVP5150 to decode PAL video, output in YUV4:2:2 format, then process it in DM365 VPFE fro...; Jacktang DSP and ARM Processors

Finally someone has explained smart manufacturing and Industry 4.0 clearly: 1. Intelligent Manufacturing and Industry 4.0 There is no universally accepted definition of intelligent manufacturing internationally, but it is generally considered to be the deep integration of new...; ohahaha RF/Wirelessly

Share a wireless Modbus communication routine of Inovance PLC with source code and instructions, download at the required speed: Staying up late to make the wireless Modbus communication routine of Huichuan PLC, dragging away at the required speed...; 人间精品在回复 Test/Measurement

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components