Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 120 to 240 ohms
for 3.3V operation.
Resistor values are typically 82 to 120 ohms
for 2.5V operation.
Figure 9. Pull-Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62
ohms and the resistor to supply is 240 ohms
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if it one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Cheap_flash_fs (FAT high-end version) -- embedded FAT16/32 file system free source code download
This code is compatible with two file systems, FAT16/FAT32, Microsoft's long file name,Chinese file nam...
Single-cell lithium battery fuel gauge, CW2015CTCC size is only 1.5*1.4mm package WLP-9The working current is 15uA and the sleep current is 0.5uA. This chip is suitable for use in small battery-powere...
I am a FPGA newbie. Recently, I was programming with Libero SoC v11.8. I defined an input pin in the top-level file. This pin was removed during synthesizing, which made it impossible to constrain thi...
Development board model: N32L43XRL_STB (5 sets in total)
From: National Technology
The main MCU chip model of the N32L43XRL_STB development board is N32L436RBL7 from National Technology, with LQFP64 p...
1 Interrupt Overview1.1 Interrupt Response Mechanism and ClassificationWhen the CPU is processing a normal program, it is sometimes required to process tasks with higher requirements, so it has to int...
1 Introduction
In microwave systems, a common component is often used, namely, a transition element that transforms one transmission line to another, called a waveform converter, also known as ...[Details]
Ultrasonic level meters are widely used in water conservancy, hydropower, municipal engineering, and fine chemical industries, wherever level measurement is involved. Despite its wide application, ...[Details]
Stack allocation of local variables
Let's analyze how the C compiler handles the allocation of local variables. For this purpose, we first give the following program:
#vi test2.c
in...[Details]
The oscilloscope current probe is crucial to the accuracy and correctness of the measurement results. It is an electronic component that connects the circuit under test to the input of the oscillosco...[Details]
According to the requirements of the regulations, the photovoltaic inverter needs to be equipped with 1~2 sets of relays on its output side, i.e., the AC side. The function of the relay is to cut o...[Details]
For a long time, the high-end intelligent driving ability lost by Ji Krypton 001 has been the core weakness that has been frantically attacked by the majority of car owners and competitors. As the ...[Details]
STM32 reads a specific GPIOx bit as 1 or 0 1 /** 2 * @brief Reads the specified input port pin. 3 * @param GPIOx: where x can be (A..G) to select the GPIO peripheral. 4 * @param GPIO_Pin: spec...[Details]
Recently, Ruiying Technology's "Liaoyuan" series of facial recognition terminals made their grand debut. Its dual-channel ISP design supports dual-camera sensors, enabling the facial recognition term...[Details]
Schematic Description:
1. The pin numbers of the common anode four-in-one 12-pin digital tube are: when the digital side of the digital tube faces the observer, the lower left corner is pin 1, ...[Details]
Solid-state lighting (SSL) or light-emitting diode (LED) lighting is the obvious replacement for incandescent and FL/CFL lighting, driven by government regulations, high efficiency, long life, and en...[Details]
Micron Technology released the company's third quarter report for fiscal year 2019. The report showed that Micron Technology's revenue in the third quarter was US$4.788 billion, compared with US$7.79...[Details]
This article will introduce some common fault diagnosis methods through several examples such as ultra-low power circuit testing, weak power supply ripple testing, online current measurement, shor...[Details]
Serial port communication is one of the most basic and important functions of microcontroller learning. The serial port can be used indirectly as a debugging interface to achieve communication betwee...[Details]
When using a megohmmeter to measure insulation resistance, pay attention to the following points:
(I) Before the test, remove the resistance and all external connection lines of the power cable...[Details]
It is precisely because of the contributions of these companies that the traditional energy-using process has begun to consider the use of electricity. In the past, we used oil and coal, so how could ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
