RP103x SERIES
LOW NOISE 150mA LDO REGULATOR
NO.EA-149-131018
OUTLINE
The RP103x Series are CMOS-based voltage regulator ICs with high output voltage accuracy, extremely low
supply current, low ON-resistance, and high ripple rejection. Each of these ICs consists of a voltage reference
unit, an error amplifier, resistor-net for voltage setting, a current limit circuit, and a chip enable circuit.
These ICs perform with low dropout voltage and a chip enable function. The line transient response and load
transient response of the RP103x Series are excellent, thus these ICs are very suitable for the power supply for
hand-held communication equipment.
The output voltage of these ICs is fixed with high accuracy. Since the packages for these ICs are
DFN(PLP)1010-4, SC-82AB, SC-88A (Non-promotion), SOT-23-5, therefore high density mounting of the ICs on
boards is possible.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
Supply Current .............................................................Typ. 36μA
Standby Mode ..............................................................Typ. 0.1μA
Dropout Voltage............................................................Typ. 0.21V (I
OUT
=150mA,
V
OUT
=2.8V)
Ripple Rejection ...........................................................Typ. 75dB (f=1kHz)
Temperature-Drift Coefficient of Output Voltage ..........Typ.
±30ppm/°C
Line Regulation ............................................................Typ. 0.02%/V
Output Voltage Accuracy..............................................±1.0%
Packages......................................................................DFN(PLP)1010-4, SC-82AB, SC-88A (Non-promotion),
SOT-23-5
Input Voltage Range.....................................................1.7V to 5.25V
Output Voltage Range ..................................................1.2V to 3.3V (0.1V steps)
(
For other voltages, please refer to MARK INFORMATIONS.)
Built-in Fold Back Protection Circuit.............................Typ. 40mA (Current at short mode)
Ceramic capacitors are recommended to be used with this IC .... 0.47μF or more
APPLICATIONS
•
•
•
•
Power source for portable communication equipment.
Power source for electrical appliances such as cameras, VCRs and camcorders.
Power source for battery-powered equipment.
Power source for home appliances.
1
RP103x
NO.EA-149-131018
BLOCK DIAGRAMS
RP103xxxxB
V
DD
V
OUT
V
DD
RP103xxxxD
V
OUT
Vref
Current Limit
Vref
Current Limit
CE
GND
CE
GND
SELECTION GUIDE
The output voltage, auto discharge function, package, and the taping type, etc. for the ICs can be selected at
the user’s request.
Product Name
RP103Kxx1∗-TR
RP103Qxx1∗-TR-FE
RP103Qxx2∗-TR-FE
RP103Nxx1∗-TR-FE
Package
DFN(PLP)1010-4
SC-82AB
SC-88A
(Non-promotion)
SOT-23-5
Quantity per Reel
10,000 pcs
3,000 pcs
3,000 pcs
3,000 pcs
Pb Free
Yes
Yes
Yes
Yes
Halogen Free
Yes
Yes
Yes
Yes
xx: The set output voltage (V
SET
) can be designated in the range from 1.2V to 3.3V in 0.1V steps.
Exception: 1.85V=RP103x18x∗5-xx
2.85V=RP103x28x∗5-xx
∗:
CE pin polarity and auto discharge function at off state are options as follows.
(B) "H" active, without auto discharge function at off state
(D) "H" active, with auto discharge function at off state
The products scheduled to be discontinued : "Non-promotion"
These products will be discontinued in the future. We advise you to select other products.
2
RP103x
NO.EA-149-131018
PIN CONFIGURATIONS
•
DFN(PLP)1010-4
Top View
4
3
•
SC-82AB
4
3
•
SC-88A
5
4
•
SOT-23-5
5
4
Bottom View
3
∗
4
(mark side)
(mark side)
(mark side)
1
2
2
1
1
2
1
2
3
1
2
3
•
PIN DESCRIPTIONS
DFN(PLP)1010-4
Pin No
1
2
3
4
Symbol
V
OUT
GND
CE
V
DD
Output Pin
Ground Pin
Chip Enable Pin ("H" Active)
Input Pin
Pin Description
∗
) The tab on the bottom of the package enhances thermal performance and is electrically connected to GND (substarate
level). It is recommended that the tab be connected to the ground plane on the board. If not, the tab can be left open.
•
SC-82AB
Pin No
1
2
3
4
Symbol
CE
GND
V
OUT
V
DD
Ground Pin
Output Pin
Input Pin
Pin Description
Chip Enable Pin ("H" Active)
•
SC-88A (Non-promotion)
Pin No
1
2
3
4
5
Symbol
CE
NC
GND
V
OUT
V
DD
No Connection
Ground Pin
Output Pin
Input Pin
Pin Description
Chip Enable Pin ("H" Active)
•
SOT-23-5
Pin No
1
2
3
4
5
Symbol
V
DD
GND
CE
NC
V
OUT
Input Pin
Ground Pin
Chip Enable Pin ("H" Active)
No Connection
Output Pin
Pin Description
3
RP103x
NO.EA-149-131018
ABSOLUTE MAXIMUM RATINGS
Symbol
V
IN
V
CE
V
OUT
I
OUT
Input Voltage
Input Voltage (CE Pin)
Output Voltage
Output Current
Power Dissipation
P
D
Power Dissipation
Power Dissipation
T
opt
T
stg
∗
∗
∗
∗
Item
Rating
6.0
6.0
−0.3
to V
IN
+0.3
180
400
380
380
420
−40
to 85
−55
to 125
Unit
V
V
V
mA
(DFN(PLP)1010-4)
(SC-82AB)
(SC-88A) (Non-promotion)
(SOT-23-5)
mW
Power Dissipation
Operating Temperature Range
Storage Temperature Range
°C
°C
∗)
For Power Dissipation, please refer to PACKAGE INFORMATION.
ABSOLUTE MAXIMUM RATINGS
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the
permanent damages and may degrade the life time and safety for both device and system using the device
in the field.
The functional operation at or over these absolute maximum ratings is not assured.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the
recommended operating conditions, even if when they are used over such conditions by momentary
electronic noise or surge. And the semiconductor devices may receive serious damage when they continue
to operate over the recommended operating conditions.
4
RP103x
NO.EA-149-131018
ELECTRICAL CHARACTERISTICS
•
RP103xxxxB/D
V
IN
= V
SET
+ 1V (V
OUT
>1.5V), V
IN
=2.5V (V
OUT
≤1.5V),
I
OUT
=1mA, C
IN
=C
OUT
=0.47µF, unless otherwise noted.
The specifications surrounded by
are guaranteed by Design Engineering at
−40°C ≤
T
a
≤
85°C.
RP103x Series
Symbol
(Ta=25°C)
Item
Ta=25°C
Conditions
V
OUT
Output Voltage
*1
-40°C
<
=
MIN.
V
OUT
x0.99
(-20mV)
V
OUT
x0.985
(-30mV)
150
TYP.
MAX.
V
OUT
x1.01
(20mV)
V
OUT
x1.015
(30mV)
Unit
V
Ta
<
=
85°C
I
OUT
ΔV
OUT
/ΔI
OUT
V
DIF
I
SS
ΔV
OUT
/ΔV
IN
RR
V
IN
ΔV
OUT
/ΔTa
I
SC
I
PD
V
CEH
V
CEL
en
R
LOW
Output Current
Load Regulation
Dropout Voltage
Supply Current
I
OUT
= 0mA
1mA
<
=
mA
10
30
mV
I
OUT
<
=
150mA
Please see the data table on next page
36
0.1
<
=
50
1.0
0.10
µA
µA
%/V
dB
Istandby Supply Current (Standby) V
CE
= 0V
Line Regulation
Ripple Rejection
Input Voltage
*2
Output Voltage
Temperature Coefficient
Short Current Limit
CE Pull-down Current
CE Input Voltage “H”
CE Input Voltage “L”
Output Noise
*3
Nch On Resistance
for Auto Discharge
(D Version Only)
BW = 10Hz to 100kHz
I
OUT
= 30mA
V
IN
= 4.0V, V
CE
= 0V
1.1
- 40°C
<
=
V
SET
+0.5V
V
IN
<
=
5.0V
0.02
75
1.7
f = 1kHz, Ripple 0.2Vp-p
V
IN
= V
SET
+1V, I
OUT
= 30mA
(In case that V
OUT
<
2.0V, V
IN
=3V)
=
5.25
±30
40
0.3
V
ppm
/°C
mA
µA
V
Ta
<
=
85°C
V
OUT
= 0V
0.3
60
30
V
µVrms
Ω
All test items listed under
Electrical Characteristics
are done under the pulse load condition (Tj≈Ta=25ºC) except for Output Noise,
Ripple Rejection, and Output Voltage Temperature Coefficient.
*
1
When V
OUT
≤2.0V,
Output voltage accuracy is
±20mV.
(When - 40°C≤Ta≤85°C, Output voltage accuracy is
±30mV)
*
2
Maximum input voltage is 5.25V. If, for any reason the input voltage exceeds 5.25V, it has to be no more than 5.5V,
and total operating time should be within 500 hours.
3
* Output noise is highly dependent on Set output voltage. Please contact us if this matters.
5
京公网安备 11010802033920号
EEWORLD
