TS972DT datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> TS972DT

TS972DT: DescriptionBasic information of TS972DT amplifier: TS972DT is an OPERATIONAL AMPLIFIER. The commonly used packaging method is SOP, TS972DT amplifier core information: The minimum operating temperature of TS972DT is -40 °C and the maximum operating temperature is 125 °C. Its maximum average bias current is 1 µA How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of TS972DT is 4 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the TS972DT gain becomes 0.707 times the low-frequency gain is 12000 kHz. The nominal supply voltage of TS972DT is 2.5 V, and its corresponding nominal negative supply voltage is -2.5 V. The input offset voltage of TS972DT is 7000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).) Related dimensions of TS972DT: The width of TS972DT is: 3.9 mm and the length is 4.9 mm. TS972DT has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 8 TS972DT amplifier additional information: Its temperature grade is: AUTOMOTIVE. The corresponding JESD-30 code is: R-PDSO-G8. The packaging code of TS972DT is: SOP. The materials of TS972DT package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The TS972DT package pin forms are: SMALL OUTLINE. Its terminal forms are: GULL WING. The maximum seat height is 1.75 mm.; CategoryAnalog mixed-signal IC Amplifier circuit; File Size114KB，12 Pages; ManufacturerSTMicroelectronics; Websitehttp://www.st.com/; Alternative parts：TS972DT

Download Datasheet Parametric View All

TS972DT Overview

Basic information of TS972DT amplifier:

TS972DT is an OPERATIONAL AMPLIFIER. The commonly used packaging method is SOP,

TS972DT amplifier core information:

The minimum operating temperature of TS972DT is -40 °C and the maximum operating temperature is 125 °C. Its maximum average bias current is 1 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of TS972DT is 4 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the TS972DT gain becomes 0.707 times the low-frequency gain is 12000 kHz.

The nominal supply voltage of TS972DT is 2.5 V, and its corresponding nominal negative supply voltage is -2.5 V. The input offset voltage of TS972DT is 7000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of TS972DT:

The width of TS972DT is: 3.9 mm and the length is 4.9 mm. TS972DT has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 8

TS972DT amplifier additional information:

Its temperature grade is: AUTOMOTIVE. The corresponding JESD-30 code is: R-PDSO-G8. The packaging code of TS972DT is: SOP. The materials of TS972DT package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR.

The TS972DT package pin forms are: SMALL OUTLINE. Its terminal forms are: GULL WING. The maximum seat height is 1.75 mm.

TS972DT Parametric

Parameter Name	Attribute value
Parts packaging code	SOIC
package instruction	SOP,
Contacts	8
Reach Compliance Code	unknown
ECCN code	EAR99
Amplifier type	OPERATIONAL AMPLIFIER
Maximum average bias current (IIB)	1 µA
Nominal Common Mode Rejection Ratio	85 dB
Maximum input offset voltage	7000 µV
JESD-30 code	R-PDSO-G8
length	4.9 mm
Negative supply voltage upper limit	-6 V
Nominal Negative Supply Voltage (Vsup)	-2.5 V
Number of functions	2
Number of terminals	8
Maximum operating temperature	125 °C
Minimum operating temperature	-40 °C
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Certification status	Not Qualified
Maximum seat height	1.75 mm
Nominal slew rate	4 V/us
Supply voltage upper limit	6 V
Nominal supply voltage (Vsup)	2.5 V
surface mount	YES
Temperature level	AUTOMOTIVE
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
Nominal Uniform Gain Bandwidth	12000 kHz
width	3.9 mm
Base Number Matches	1

Recommended Resources

Touch control circuit diagram

LT1111 working principle diagram (a)

Low power consumption and high power regulator circuit

Automobile antenna automatic telescopic control circuit

Low power consumption, 5V drive, temperature compensated crystal oscillator circuit

CX23040 (TV and VCR) infrared remote control transmitter circuit

Some problems encountered when using spartan6 PLL IP Core: [i=s]This post was last edited by VincentLee90 on 2019-10-13 21:34[/i]Some problems encountered when using spartan6 PLL IP CoreProblem 1 : The external clk is used as the global input clock to provide...; VincentLee90 FPGA/CPLD

Books purchased with E-coins: Dangdang.com is having a discount promotion again, and I couldn't help but buy it again. I happened to see the administrator online, so I considered using E coins to exchange for 6 books, which is not...; cruelfox Talking

How can I most effectively avoid arcing damage to the two contacts when the two contacts of the relay in an electric energy meter are opened or closed?: How can I most effectively avoid arcing damage to the two contacts when the two contacts of the relay in an electric energy meter are opened or closed?...; 一沙一世 stm32/stm8

What is Wi-Fi and why is it important?: What is a wireless network? Generally speaking, Wi-Fi refers to wireless LAN technology that utilizes the IEEE 802.11 standard for communication. Wi-Fi products use radio waves to transmit data from c...; 石榴姐 RF/Wirelessly

I need help from you guys, the inductor in the step-down power supply circuit makes a loud sound, what's going on?: Please help, heroes. The following is a step-down power supply circuit. When debugging, the inductor makes a sound. What's going on?...; Knight97538 Power technology

RIID emits a weak signal: Hello, I have a biological weak signal of 10uA, frequency 1K, amplitude not exceeding 0.5V. I want to use RC522 to send itto the corresponding mobile phone and display the current value through a dedi...; QWE4562009 Analog electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components