FSK-13.25MA-20 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> FSK-13.25MA-20

FSK-13.25MA-20: DescriptionINTERCONNECTION DEVICE; CategoryThe connector The connector; File Size181KB，3 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

FSK-13.25MA-20 Overview

INTERCONNECTION DEVICE

FSK-13.25MA-20 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
Other features	KAPTON
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

Flexible Interconnections

Flexstrip

ESCRIPTION

PPLICATION

FLEXSTRIP

Jumpers are multi-

conductor board-to-board interconnect

devices, pre-plated and ready to use -

without wire stripping, cutting to length,

or solder preparation. They provide a

convenient, reliable alternative to

conventional point-to-point wiring for

high density, high-vibration PC board

interconnect applications.

FLEXSTRIP

Jumpers may be

repeatedly flexed without failure.

Flat/round conductor design and

one-piece

construction

give

vibration-proof reliability and longer

life than conventional wiring systems.

FLEXSTRIP

JUMPERS

ESIGN

DVANTAGES

• One-piece construction.

• Round copper conductors rolled

flat for high flex life, tin-plated for

easy soldering.

• Round-to-flat transition zone permits

flexing stress to be distributed

evenly throughout flat conductor area.

• Round-to-flat

design

provides

vibration-proof reliability and long life.

• Round-to-flat transition zone acts

as a hinge between PC boards;

allows boards to be opened for

fabrication and servicing, then

closed for compactness.

• Round pin ends facilitate PC board

insertion and long life.

• Choice of conductor pitch to

accommodate virtually any PCB

hole

pattern;

tightly

held

tolerances.

• Available in 4 insulations for high

volume commercial use as well as

military/aerospace applications.

• Jumpers may be “connectorized”

to mate with other industry-

standard headers.

• Jumpers may be used as part of

FLEXPAC

assemblies.

LR49571

E60980

Loop

Diameter

Flex Cycles

(in Millions)

Loop Diameter (inches)

Thomas & Betts Electronics/OEM Division Tel: 901-252-5000 Fax: 901-252-1312

157

Recommended Resources

9012, 9013 OTL discrete component power amplifier circuit diagram

Electric fence charger

Circuit diagram of a sound and light dual control indicator light

Long delay constant current charging circuit circuit diagram

Using SH805 sound and light dual control high-power colorful lights with birdsong sound circuit

Computer motherboard circuit diagram 820 1_59

PCB wiring and layout and circuit design 268 design specifications: This article summarizes 268 design specifications for PCB wiring and layout and circuit design, and shares them with you...; 造物工场 PCB Design

[ESK32-360 Review] + Construction of development environment: [i=s]This post was last edited by jinglixixi on 2020-7-27 07:58[/i]The ESK32-360 development board supports a wide range of development tools, which can be seen from the folder of the routines, as sho...; jinglixixi Domestic Chip Exchange

Several circuit designs that must be understood by microcontrollers: 1. Selection of pull-up resistor for MCU　　You can see that when the resistor R1=10k in the reset circuit, RST is high level, and when R1=50, RST is low level. It is obvious that when R1=10k, it is wro...; Jacktang Microcontroller MCU

Several questions about common source amplifier circuits.: The static part of the common source amplifier circuit is shown in the figure. In the figure, R1 is connected to a 5W resistor. When the static working point is adjusted by 12V, the GS voltage is arou...; 小宇文 Analog electronics

Reliable communications for short-range wireless systems: Ensuring the reliability of communication and meeting the stringent requirements of service quality are important issues in short-range wireless communication systems. The key characteristics of short...; arui1999 Download Centre

I can't read the TMP275 temperature sensor. I use the STM32 I/O to simulate IIC. Please help.: uchar R_word; uchar ACK_Flag;uchar read_buffer_iic[16];uchar write_buffer_iic[16]; void Start(void){TSDA_IO_OUT();TSCL_IO_OUT();TSDA=1;TSCL=1;delay_us(10);TSDA=0;delay_us(10);TSCL=0;delay_us(10);} voi...; tea717 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components