Type 418P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
FEATURES
•
Identical performance characteristics to Type
225P pressed polyester capacitors through 600
WVDC ratings
RoHS
•
Wound from PETP polyester film and thin gauge
COMPLIANT
foil under carefully controlled atmospheric
conditions
•
Protected against moisture by a conformal coating of
epoxy
•
Specifically designed for printed wiring board applications
•
Widely used in computers, instrumentation and
telecommunications equipment
PERFORMANCE CHARACTERISTICS
Operating Temperature:
- 55 °C to + 85 °C, standard; up to
+ 105 °C when WVDC is reduced to 70 % of + 85 °C rating.
To + 125 °C when WVDC is 50 % of + 85 °C rating.
Insulation Resistance:
After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C
≤
0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C
≤
0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C
≤
0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C
≤
0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency for 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %.
Dielectric Withstanding Voltage:
Capacitors rated below 1000 volts shall withstand a DC
potential of 250 % of rated voltage applied between terminals
for not more than 5 seconds. Capacitance rated 1000 volts
and above shall withstand a DC potential of 200 % of rated
voltage applied between the terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
DIMENSIONS
in inches [millimeters]
L
Max.
L
Max.
L
Max.
D
Max.
0.237
[6.019]
Max.
1.250
[31.750]
Min.
Lead
Length
0.237
[6.019]
Max.
Lead
Length
0.237
[6.019]
Max.
S
± 0.060 [1.524]
S
± 0.030 [0.762]
S
± 0.030 [0.762]
0.032 [0.813] Dia.
(No. 20 AWG)
Tinned Copper-Clad Steel
Terminal A
Case
Code
J
K
L
M
L
(Max.)
Terminal B
Terminal D
S
Terminal A and B
0.500 [12.700]
0.688 [17.475]
0.969 [24.613]
1.344 [34.138]
Terminal D
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
1.094 [27.788]
0.70 [17.78]
0.90 [22.86]
1.20 [30.48]
1.60 [40.64]
Document Number: 42017
Revision: 16-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
25
Type 418P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
DISSIPATION FACTOR VS. TEMPERATURE
1.5
% DISSIPATION /1000Hz
CAPACITANCE CHANGE
16
14
12
!0
CAPACITANCE CHANGE ENVELOPE
8
FOR 96 % CONFIDENCE LEVEL
6
4
2
0
2
4
6
- 55 - 40 - 25
0
+ 25
+ 50
+ 75 +
85
+ 105 + 125
- 50
+ 100
TEMPERATURE DEG. CENTIGRADE
% CAPACITANCE CHANGE/1000Hz
1.0
TYPICAL
.5
0
- 55 - 40 - 25
- 50
0
+ 25
+ 50
+ 75 +
85
+ 105 + 125
+ 100
TEMPERATURE DEG. CENTIGRADE
STANDARD RATINGS*
µF
± 10
%
TOLERANCE
0.027
0.033
0.047
0.082
0.1
0.15
0.22
0.33
0.47
0.68
1.0
0.0056
0.0068
0.01
0.015
0.018
0.022
0.033
0.039
0.047
0.056
0.068
0.082
0.1
0.15
0.22
0.27
0.33
0.47
SIZE
PART NUMBER
100 VDC/70 VAC**
418P27391J
418P33391J
418P47391J
418P82391K
418P10491K
418P15491K
418P22491L
418P33491L
418P47491M
418P68491M
418P10591M
418P56292J
418P68292J
418P10392J
418P15392J
418P18392J
418P22392J
418P33392K
418P39392K
418P47392K
418P56392L
418P68392L
418P82392L
418P10492L
418P15492L
418P22492L
418P27492M
418P33492M
418P47492M
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
1.20 [30.48]
1.20 [30.48]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
200 VDC/140 VAC**
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
0.35 [8.89]
0.35 [8.89]
0.35 [8.89]
0.40 [10.16]
0.40 [10.16]
0.45 [11.43]
0.45 [11.43]
0.50 [12.70]
0.50 [12.70]
0.60 [15.24]
0.70 [17.78]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.38 [9.65]
0.38 [9.65]
0.38 [9.65]
0.38 [9.65]
0.38 [9.65]
0.40 [10.16]
0.40 [10.16]
0.45 [11.43]
0.50 [12.70]
0.47 [11.94]
0.47 [11.94]
0.55 [13.97]
L
H
* These standard ratings are available through Sprague
®
distribution on special order. For complete Part Number, add letter and number for
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3).
** 60 Hz rms
www.vishay.com
26
For technical questions, contact: spresale@vishay.com
Document Number: 42017
Revision: 16-Feb-07
Type 418P
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
STANDARD RATINGS*
in inches [millimeters]
L
400 VDC/200 VAC**
0.001
418P10294J
0.70 [17.78]
0.0015
418P15294J
0.70 [17.78]
0.0022
418P22294J
0.70 [17.78]
0.0033
418P33294J
0.70 [17.78]
0.0047
418P47294J
0.70 [17.78]
0.0068
418P68294J
0.70 [17.78]
0.0082
418P82294J
0.70 [17.78]
0.01
418P10394J
0.70 [17.78]
0.015
418P15394J
0.70 [17.78]
0.018
418P18394K
0.90 [22.86]
0.022
418P22394K
0.90 [22.86]
0.033
418P33394K
0.90 [22.86]
0.047
418P47394L
1.20 [30.48]
0.056
418P56394L
1.20 [30.48]
0.068
418P68394L
1.20 [30.48]
0.082
418P82394L
1.20 [30.48]
0.1
418P10494L
1.20 [30.48]
0.15
418P15494L
1.20 [30.48]
0.18
418P18494M
1.60 [40.64]
0.22
418P22494M
1.60 [40.64]
0.27
418P27494M
1.60 [40.64]
0.33
418P33494M
1.60 [40.64]
0.39
418P39494M
1.60 [40.64]
0.47
418P47494M
1.60 [40.64]
600 VDC/200 VAC**
0.001
418P10296J
0.70 [17.78]
0.0012
418P12296J
0.70 [17.78]
0.0015
418P15296J
0.70 [17.78]
0.0018
418P18296J
0.70 [17.78]
0.0022
418P22296J
0.70 [17.78]
0.0027
418P27296J
0.70 [17.78]
0.0033
418P33296J
0.70 [17.78]
0.0039
418P39296J
0.70 [17.78]
0.0047
418P47296J
0.70 [17.78]
0.0056
418P56296J
0.70 [17.78]
0.0068
418P68296J
0.70 [17.78]
0.0082
418P82296K
0.90 [22.86]
0.01
418P10396K
0.90 [22.86]
0.012
418P12396K
0.90 [22.86]
0.015
418P15396K
0.90 [22.86]
0.018
418P18396K
0.90 [22.86]
0.022
418P22396K
0.90 [22.86]
0.027
418P27396L
1.20 [30.48]
0.033
418P33396L
1.20 [30.48]
0.039
418P39396L
1.20 [30.48]
0.047
418P47396L
1.20 [30.48]
0.056
418P56396L
1.20 [30.48]
0.068
418P68396L
1.20 [30.48]
0.082
418P82396L
1.20 [30.48]
0.1
418P10496L
1.20 [30.48]
0.12
418P12496M
1.60 [40.64]
0.15
418P15496M
1.60 [40.64]
0.18
418P18496M
1.60 [40.64]
0.22
418P22496M
1.60 [40.64]
0.25
418P25496M
1.60 [40.64]
* These standard ratings are available through Sprague
®
distribution on special order. For complete Part Number,
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3).
** 60 Hz rms
µF
± 10
%
TOLERANCE
SIZE
PART NUMBER
H
0.30 [7.62]
0.30 [7.62]
0.30 [7.62]
0.30 [7.62]
0.30 [7.62]
0.33 [8.38]
0.35 [8.89]
0.35 [8.89]
0.38 [9.65]
0.38 [9.65]
0.38 [9.65]
0.40 [10.16]
0.40 [10.16]
0.45 [11.43]
0.45 [11.43]
0.52 [13.21]
0.52 [13.21]
0.57 [14.48]
0.60 [15.24]
0.60 [15.24]
0.65 [16.51]
0.65 [16.51]
0.72 [18.29]
0.80 [20.32]
0.30 [7.62]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.33 [8.38]
0.35 [8.89]
0.35 [8.89]
0.38 [9.65]
0.38 [9.65]
0.40 [10.16]
0.40 [10.16]
0.40 [10.16]
0.40 [10.16]
0.40 [10.16]
0.40 [10.16]
0.45 [11.43]
0.45 [11.43]
0.45 [11.43]
0.45 [11.43]
0.55 [13.97]
0.55 [13.97]
0.60 [15.24]
0.60 [15.24]
0.65 [16.51]
0.65 [16.51]
0.70 [17.78]
0.70 [17.78]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
add letter and number for
Vishay Sprague
Document Number: 42017
Revision: 16-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
27
Type 418P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
STANDARD RATINGS
in inches [millimeters]
µF
± 10
%
TOLERANCE
0.001
0.0015
0.0018
0.0022
0.0033
0.0047
0.0056
0.0068
0.0082
0.01
0.015
0.018
0.022
0.027
0.033
0.039
0.047
0.056
0.068
0.082
0.1
SIZE
PART NUMBER
418P102910J
418P152910J
418P182910J
418P222910J
418P332910K
418P472910K
418P562910K
418P682910K
418P822910K
418P103910K
418P153910L
418P183910L
418P223910L
418P273910L
418P333910L
418P393910M
418P473910M
418P563910M
418P683910M
418P823910M
418P104910M
L
1000 VDC/200 VAC**
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.70 [17.78]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
0.90 [22.86]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.20 [30.48]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
1.60 [40.64]
H
0.33 [8.38]
0.33 [8.38]
0.35 [8.89]
0.35 [8.89]
0.35 [8.89]
0.40 [10.16]
0.43 [10.92]
0.43 [10.92]
0.48 [12.19]
0.48 [12.19]
0.48 [12.19]
0.58 [14.73]
0.58 [14.73]
0.65 [16.51]
0.65 [16.51]
0.65 [16.51]
0.65 [16.51]
0.75 [19.05]
0.75 [19.05]
0.85 [21.59]
0.85 [21.59]
* These standard ratings are available through Sprague
®
distribution on special order. For complete Part Number, add letter and number for
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3)
** 60 Hz rms
ORDERING INFORMATION
418P
TYPE
104
CAPACITANCE
Capacitance is
expressed in
picofarads. The
first two digits are
significant. The
third is the number
of zeros to follow.
Values must
conform to Decade
Rating for the
tolerance
specified.
9
1
TOLERANCE DC VOLTAGE
RATING
0 = ± 20 %
9 = ± 10 %
5=±5%
This is
expressed in
hundred of
volts.
J, K, L or M
CASE CODE
See Dimensional
Configurations
D
TERMINAL
3
LEAD LENGTH
(-XXX)
SPECIAL
CONSTRUCTION
A three-digit suffix
may be added by
the factory to
denote special
construction.
1 = 0.187" ± 0.030"
A = Straight Lead
[4.750 ± 0.762]
B = Hairpin Crimped
D = Hockey Crimped 2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250" [31.750]
Minimum
www.vishay.com
28
For technical questions, contact: spresale@vishay.com
Document Number: 42017
Revision: 16-Feb-07
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
