EEWORLDEEWORLDEEWORLD

Part Number

Search

RT9818G-50GV

Description
IC VOLT DETECTOR 1.2V SOT23-3
Categorysemiconductor    Analog mixed-signal IC   
File Size191KB,14 Pages
ManufacturerRichtek Technology Corporation
Websitehttps://www.richtek.com/
Download Datasheet View All

RT9818G-50GV Overview

IC VOLT DETECTOR 1.2V SOT23-3

®
RT9818
Micro-Power Voltage Detectors
General Description
The RT9818 is a micro-power voltage detector supervising
the power supply voltage level for microprocessors (μP)
or digital systems. It provides internally fixed threshold
levels with 0.1V per step ranging from 1.2V to 5V, which
covers most digital applications. It features low supply
current of 3μA. The RT9818 performs supervisory function
by sending out a reset signal whenever the V
DD
voltage
falls below a preset threshold level. This reset signal will
last the whole period before V
DD
recovering. Once V
DD
recovered upcrossing the threshold level, the reset signal
will be released after a
certain delay time. RT9818 is
provided in SC-82, SC-70-3, SOT-23-3, SOT-23-5 and
SOT-89 packages.
Features
Internally Fixed Threshold 1.2V to 5V in 0.1V Step
High Accuracy
±
1.5%
Low Supply Current 3μA
μ
No External Components Required
Quick Reset within 20μs
μ
Built-In Recovery Delay Include 0ms, 55ms, 220ms,
450ms Options
Low Functional Supply Voltage 0.9V
N-Channel Open-Drain Output
Small SC-82, SC-70-3, SOT-23-3, SOT-23-5, SOT-89
Packages
RoHS Compliant and 100% Lead (Pb)-Free
Applications
Ordering Information
RT9818
-
Package Type
U3 : SC-70-3
V : SOT-23-3
VL : SOT-23-3 (L-Type)
B : SOT-23-5
X : SOT-89
Y : SC-82
YR : SC-82 (R-Type)
Lead Plating System
P : Pb Free
G : Green (Halogen Free and Pb Free)
Threshold Voltage
12 : 1.2V
13 : 1.3V
:
49 : 4.9V
50 : 5.0V
Reset Active Timeout Period
A = 0ms
(RESET)
B = 55ms
(RESET)
C = 220ms
(RESET)
D = 450ms
(RESET)
E = 0ms
(RESET)
F = 55ms
(RESET)
G = 220ms
(RESET)
H = 450ms
(RESET)
Computers
Controllers
Intelligent Instruments
Critical
μP
and
μC
Power Monitoring
Portable/Battery-Powered Equipment
Marking Information
For marking information, contact our sales representative
directly or through a Richtek distributor located in your
area.
Typical Application Circuit
100k
Pull Up
VDD
P
RESET/
RESET
RT9818
GND
VDD
RESET/
RESET
Note :
½
Richtek products are :
RoHS compliant and compatible with the current require-
ments of IPC/JEDEC J-STD-020.
½
Suitable for use in SnPb or Pb-free soldering processes.
is a registered trademark of Richtek Technology Corporation.
Copyright
©
2016 Richtek Technology Corporation. All rights reserved.
DS9818-11 August 2016
www.richtek.com
1
[Hua Diao Experience] 16 Use Beetle ESP32 C3 to control 8X32-bit WS2812 hard screen
[i=s]This post was last edited by eagler8 on 2022-7-9 04:56[/i]The hardware used in the experiment and the software platform used Arduino IDE (see "【Hua Diao Experience】15 Try to build the Arduino dev...
eagler8 DIY/Open Source Hardware
It’s hard to believe that this pair of high-speed signals changed the vias so many times!!!
Author: Huang Gang, a member of Yibo Technology Expressway MediaPCB engineer: "There are no more layers to go. These pairs of 10G signals need to change layers several times and make four vias before ...
yvonneGan PCB Design
What is the purpose of adding a capacitor to the source and drain of a MOS tube?
In many places, we see a capacitor added to the source and drain of a MOS tube. What is the function of this capacitor?...
Knight97538 Power technology
Introduction to the development history of ARM architecture
So far ( 2016 ), the ARM architecture has developed to the eighth generation ARMv8 . Before understanding the latest architecture, it is necessary to review the development history of ARM architecture...
bandy ARM Technology
[Infineon XENSIV PAS CO2 sensor] Simple unboxing
Thanks to the manufacturer and eeworld's event, this is a XENSIV PAS CO2 sensor from Infineon. I couldn't wait to open it after receiving it, and I give a thumbs up to the packaging.Close-up of the se...
dql2016 Sensor
The boost circuit designed by LM5022 has only a 0.67V sawtooth wave at the OUT end.
The parameters simulated by webench are 24V input and 30V@4A output. It seems that the chip is not working. The OUT terminal is a sawtooth wave. VCC=7.4V, VFB=1V, VCOMP=0.8V...
Foxsw Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号