NJM78L05UA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> Power management> NJM78L05UA

NJM78L05UA: DescriptionIC REG LINEAR 5V 100MA SOT89; Categorysemiconductor Power management; File Size190KB，8 Pages; ManufacturerNJR Corporation NJRC; Environmental Compliance

Download Datasheet Parametric View All

NJM78L05UA Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	NJM78L05UA	-	-	View	Buy Now

NJM78L05UA Overview

IC REG LINEAR 5V 100MA SOT89

NJM78L05UA Parametric

Parameter Name	Attribute value
Output configuration	just
Output type	fixed
Number of voltage regulators	1
Voltage - input (maximum)	30V
Voltage - Output (minimum/fixed)	5V
Voltage - Output (maximum)	-
Pressure drop (maximum)	-
Current - Output	100mA
Current - static (Iq)	6mA
PSRR	69dB（120Hz）
Control characteristics	-
Protective function	Overtemperature, short circuit
Operating temperature	-40°C ~ 85°C
Installation type	surface mount
Package/casing	TO-243AA
Supplier device packaging	SOT-89

Preview

Download Datasheet

View All

NJM78L00

3-TERMINAL POSITIVE VOLTAGE REGULATOR

■

GENERAL DESCRIPTION

The

NJM78L00

series of 3-Terminal Positive Voltage Regulators

is constructed using the New JRC Planar epitaxial process. These

regulators employ internal current-limiting and thermal-shutdown,

making them essentially indestructible. If adequate heat sinking is

provided, they can deliver up to 100mA output current. They are

intended as fixed voltage regulators in a wide range of applications

including local or on-card regulation for elimination of noise and

distribution problems associated with single-point regulation. In

addition, they can be used with power pass elements to make

high-current voltage regulators. The

NJM78L00

series used as a

Zener diode/resistor combination replacement, offers an effective

output impedance improvement of typically two orders of

magnitude, along with lower quiescent current and lower noise.

■

PACKAGE OUTLINE

(TO-92)

(SOT-89)

NJM78L00A

1.OUT

2.GND

3.IN

NJM78L00UA

1.OUT

2.GND

3.IN

■

FEATURES

●

Internal Short Circuit Current Limit

●

Internal Thermal Overload Protection

●

Excellent Ripple Rejection

●

Guarantee’d 100mA Output Current

●

Package Outline

●

Bipolar Technology

TO-92, SOT-89

■

EQUIVALENT CIRCUIT

Ver.2003-07-18

-1-

Recommended Resources

Ultrasonic remote control lighting switch circuit a

Shuanglu brand BCD-182 refrigerator circuit

Inductive automatic doorbell circuit

Level display circuit diagram

Starting circuit composed of relays, etc.

DZW75-48/50(50II) high frequency rectifier filter circuit

What is the function of the cross connection of the five tubes in the middle of this comparator?: What is the function of the cross-connection of the five tubes in the middle of this comparator? The test shows that it is a falling edge trigger. Where is the falling edge trigger? Please help. It wo...; 真让人头大55 Analog electronics

Understanding of TIMERA timing interrupt of MSP430F149: [size=4]The code is as follows: [/size] [size=4] [/size] [size=4]//This platform is msp430f149 [/size] [size=4]#include#include[/size] [size=4] [/size] [size=4]volatile unsigned char count = 0,flag = ...; fish001 Microcontroller MCU

What is the difference between pyb.delay and time.sleep?: It’s still Xiaobai’s problem. When learning micropython, I came across pyb.delay and time.sleep, both of which can achieve delay. What is the difference between them, or what impact do they have on th...; ywb888 MicroPython Open Source section

Stepper motor current test: In the above figure, the red dotted line is the current on the motor phase line, and the blue line is the voltage on the phase line. The current probes from Tektronix and Keysight are too expensive an...; S3S4S5S6 Analog electronics

【DIY Creative LED】Effect Demonstration: [i=s]This post was last edited by dcexpert on 2020-10-6 18:16[/i]Let's first demonstrate the running effect, which is completely controlled by touch keys.Start : Touch both touch keys at the same time...; dcexpert MCU

[GD32450I-EVAL] USART and DMA variable length reception: [i=s] This post was last edited by tinnu on 2020-10-25 23:18[/i](1) Enable DMA The recommended DMA sending USART mode in the routine: void USART_DMA_Init(void) {dma_single_data_parameter_struct dma_in...; tinnu GD32 MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components