Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
CC
= full range, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at V
CC
= +5.0V and T
A
= +25°C, reset not
asserted.) (Note 1)
PARAMETER
Supply Voltage Range
(Note 2)
Supply Current
SYMBOL
V
CC
CONDITIONS
MAX6800/MAX6801
T
A
= 0°C to +125°C
MAX6802
MAX6800/MAX6801
T
A
= -40°C to +125°C
MAX6802
V
CC
= +3.0V
No load
V
CC
= +5.0V
MAX680_UR_ _D_-T,
Table 1
V
CC
falling at 10V/ms
MAX680_UR_ _D1-T
MAX680_UR_ _D2-T
MAX680_UR_ _D3-T
Reset
asserted
Reset not
asserted
Reset
asserted
Reset not
asserted
I
SINK
= 50µA, V
CC
≥ 1.0V
I
SINK
= 1.2mA, V
CC
≥ 2.5V
t
RP
T
A
= +25°C
T
A
= -40°C to +125°C
MIN
0.7
1.0
0.78
1.2
TYP
MAX
5.5
5.5
5.5
5.5
10
12
V
TH
+ 1.8%
V
TH
+ 3%
2
40
200
0.4
0.3
0.4
0.8 x V
CC
0.8 x V
CC
0.8 x V
CC
0.8 x V
CC
0.3
0.4
V
0.8 x V
CC
V
V
ms
UNITS
V
I
CC
4
5
V
TH
- 1.8%
V
TH
- 3%
1
20
100
V
TH
V
TH
30
1.5
30
150
µA
Reset Threshold
V
CC
Falling Reset Delay
Reset Active Timeout Period
V
TH
V
µs
RESET
Output Low-Voltage
(MAX6801/MAX6802)
RESET
Output High-Voltage
(MAX6801)
V
OL
V
OH
V
OH
V
OL
I
SOURCE
= 500µA, V
CC
≥ 3.0V
I
SOURCE
= 1µA, V
CC
≥ 1.0V
I
SOURCE
= 800µA, V
CC
≥ 5.0V
I
SOURCE
= 200µA, V
CC
≥ 1.8V
I
SINK
= 1.2mA, V
CC
≥ 4.25V
RESET Output Voltage
(MAX6800)
I
SINK
= 1.2mA, V
CC
≥ 3.0V
I
SINK
= 3.2mA, V
CC
≥ 5.0V
I
SOURCE
= 800µA, V
CC
≥ 4.25V
RESET
Output Leakage Current
0.5
µA
V
CC
> V
TH
,
RESET
not asserted
(MAX6802)
Note 1:
All parts are production tested at T
A
= +25°C. Overtemperature limits are guaranteed by design and not production tested.
Note 2:
I
SOURCE
for the MAX6800 is 100nA. I
SINK
for the MAX6801 is 100nA. I
SINK
for the MAX6802 is 50μA.
www.maximintegrated.com
Maxim Integrated │
2
MAX6800/MAX6801/
MAX6802
Typical Operating Characteristics
3-Pin, Low-Power
μP Reset Circuits
(Reset not asserted, T
A
= +25°C, unless otherwise noted.)
NORMALIZED RESET TIMEOUT PERIOD
vs. TEMPERATURE
MAX6800/01/02 toc01
MAX6800/01/02 toc02
SUPPLY CURRENT vs. TEMPERATURE
6.5
6.0
5.5
I
CC
(µA)
5.0
4.5
4.0
3.5
3.0
-50
-25
0
25
50
75
100
125
V
CC
= +3.3V
V
CC
= +5.0V
1.050
NORMALIZED RESET TIMEOUT PERIOD
1.040
1.030
1.020
1.010
1.000
0.990
0.980
0.970
0.960
0.950
RESET
(V
OL
)
vs. SUPPLY VOLTAGE
T
A
= +125°C
60
T
A
= +85°C
40
T
A
= +25°C
T
A
= -40°C
V
TH
= 2.93V
I
SINK
= 500mA
RESET
ASSERTED
MAX6801/MAX6802
MAX6800/01/02 toc03
80
OUTPUT VOLTAGE LOW (mV)
20
-50
-25
0
25
50
75
100
125
0
1.0
1.5
2.0
V
CC
(V)
2.5
3.0
TEMPERATURE (°C)
TEMPERATURE (°C)
RESET (V
OH
)
vs. SUPPLY VOLTAGE
MAX6800/01/02 toc04
OUTPUT VOLTAGE HIGH (V
CC
- V
OH
) (mV)
MAXIMUM TRANSIENT DURATION (µs)
75
PROPAGATION DELAY (µs)
V
TH
= 2.93V
I
SOURCE
= 100A
RESET ASSERTED
(MAX6800)
T
A
= +125°C
T
A
= +85°C
T
A
= +25°C
MAX6800/01/02 toc05
500
400
300
200
100
0
RESET DOES
NOT OCCUR
0.1
RESET OCCURS
90
80
70
60
50
40
30
20
10
0
V
CC
= FALLING AT 10V/ms
-50
-25
0
25
50
75
100
V
CC
= FALLING AT 1V/ms
50
25
T
A
= -40°C
1.0
1.5
2.0
V
CC
(V)
0
2.5
3.0
100
1000
RESET COMPARATOR OVERDRIVE (mV)
1
10
125
TEMPERATURE (°C)
www.maximintegrated.com
Maxim Integrated │ 3
MAX6800/01/02 toc06
100
600
MAXIMUM TRANSIENT DURATION
vs. RESET COMPARATOR OVERDRIVE
100
V
CC
FALLING PROPAGATION DELAY
vs. TEMPERATURE
MAX6800/MAX6801/
MAX6802
Pin Configuration
TOP VIEW
GND 1
3-Pin, Low-Power
μP Reset Circuits
MAX6800
MAX6801
MAX6802
3 V
CC
RESET
(RESET) 2
SOT23-3
( ) ARE FOR MAX6800
Pin Description
PIN
MAX6800
1
—
MAX6801/
MAX6802
1
2
NAME
GND
Ground
Active-Low Reset Output.
RESET
is asserted while V
CC
is below the reset
threshold and remains asserted for a reset timeout period (t
RP
) after V
CC
rises above the reset threshold.
RESET
on the MAX6801 is push/pull.
RESET
on the MAX6802 is open-drain.
Active-High Reset Output. RESET is asserted while V
CC
is below the reset
threshold and remains asserted for a reset timeout period (t
RP
) after V
CC
rises above the reset threshold. RESET on the MAX6800 is push/pull.
Supply Voltage Input
FUNCTION
RESET
2
3
—
3
RESET
V
CC
www.maximintegrated.com
Maxim Integrated │ 4
MAX6800/MAX6801/
MAX6802
Applications Information
Interfacing to μPs with Bidirectional
Reset Pins
Since the
RESET
output on the MAX6802 is open-
drain, this device interfaces easily with μPs that have
bidirectional reset pins, such as the Motorola 68HC11.
Connecting the μP supervisor’s
RESET
output directly to
the microcontroller’s (μC’s)
RESET
pin with a single pullup
resistor allows either device to assert reset (Figure
1).
In addition to issuing a reset to the μP during
power-up, power-down, and brownout conditions, these
devices are relatively immune to short-duration, negative-
going V
CC
transients (glitches). The
Typical Operating
Characteristics
show the Maximum Transient Duration
vs. Reset Comparator Overdrive graph. The graph shows
the maximum pulse width that a negative-going V
CC
transient may typically have without issuing a reset signal.
As the amplitude of the transient increases, the maximum
allowable pulse width decreases.
3-Pin, Low-Power
μP Reset Circuits
Ensuring a Valid Reset Output Down to
V
CC
= 0V
Negative-Going V
CC
Transients
When V
CC
falls below 1V and approaches the minimum
operating voltage of 0.7V, push/pull-structured reset
The interface of the three-phase DC brushless controller is shown in the figure.The control port (left side) has a hole spacing of 2.0:5V - the control board outputs 5V internally, which can provide a...
Source: Procuratorate Daily
Dissatisfied with being fired by the company, he wrote a "crawler" program and implanted it into the control platform website, deleting the company's relevant data codes, c...
The surging 5G tide will bring important challenges to the RF front end. The mobile phone antenna will also face unprecedented tests after the arrival of 5G. From 4G to the current 5G, MIMO has gradua...
I just changed to a new company and they asked me to use Allegro. I had been using Ad before, but I found that the half-layer colors of Allegro are really difficult to distinguish. Plus, I'm not very ...
In an AC circuit containing resistance, inductance and capacitance, the voltage across the circuit is generally out of phase with the current. If the circuit parameters or the power supply frequency a...
In embedded development, we sometimes need to check the usage of the target chip FLASH and RAM area after compilation. Most IDEs disable this function by default. In this case, we can manually enable ...
Test to determine the alignment and endianness of Atmega16 Post the results first: - Little endian mode - No alignment requirement (1 byte alignment) Test code // Test variables struct { uint...[Details]
IMDT launches new SOMs and SBCs equipped with the latest RENESAS RZ/V2H SOC to serve high-performance robotic applications with visual AI and real-time control capabilities The V2H-based SOM (syste...[Details]
As the Samsung Galaxy S10 5G version will be officially launched tomorrow (April 5), South Korea's three major telecom operators SKT, KT, and LG Uplus all launched their own 5G data packages yesterda...[Details]
The smart LED light is based on the STC89C52RC microcontroller design and has two modes: automatic and manual: 1) Automatic mode, which can use an overheating infrared sensor to detect whether there ...[Details]
Abstract This paper discusses the implementation of information collection for workshop monitoring systems using barcodes as information carriers, analyzes the required information and its barco...[Details]
1. Structural features of the detector
The detector uses a single-chip microcomputer to control a reflective infrared sensor to detect the position of the driver's head. By detecting the relat...[Details]
There are many cross-border power battery companies, many of which have made great achievements in the field of technology, such as Huawei, Tencent, Meituan, etc. They mainly invest in related batter...[Details]
Since when, China has added a new label of "infrastructure maniac". From the increasingly complete domestic transportation system to the high-speed rail and 5G exported overseas, China is indeed beco...[Details]
1 Introduction to Digital Multimeter Digital measuring instruments have become mainstream because they have high sensitivity, high accuracy, clear display, strong overload capacity, are easy to carry...[Details]
1. Purpose Due to project requirements, it is necessary to realize the communication between the S3C2440 serial port and the PC. Through the serial port communication examples in the experiment manua...[Details]
In the previous article, I didn’t finish talking about the probe function corresponding to the LCD device driver. This article will continue to talk about the probe function. s3cfb_pre_init(); Last...[Details]
(Photo source: nouryon official website) According to foreign media reports, Nouryon Polymer Chemicals has begun delivering AkuPure, a carboxymethyl cellulose polymer specifically for lithium-ion ...[Details]
Wiring method Please use the thick wire in the test wire to connect the current loop, and use the thin wire in the test wire to connect the voltage loop. (This instrument is equipped with a set of 4×...[Details]
Micron Technology Inc., a supplier of memory and storage solutions, has released its fifth annual sustainability report. In the report, Micron reiterated its vision to enrich people's lives by changi...[Details]
A soft starter is a device used to start and control a motor. It adjusts the starting current and voltage of the motor to achieve smooth starting and stopping of the motor. The soft starter paramet...[Details]
Motor Drive Control（Motor Control）
京公网安备 11010802033920号
EEWORLD
