Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature (Note 1) ................................+235°C
Note 1:
The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, T
A
= -40°C to +85°C. Typical specifications are at T
A
= +25°C,
unless otherwise noted.) (Note 2)
PARAMETER
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
TM
Threshold
SET Input Leakage Current
1mA
≤
I
OUT
≤
150mA, T
A
= +25°C
1mA
≤
I
OUT
≤
150mA, T
A
= -40°C to +85°C
1mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
100mA, T
A
= +25°C
2mA
≤
I
OUT
≤
100mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
(Note 3)
V
SET
I
SET
V
SET
= 0, +1.2V (Note 3)
SYMBOL
V
IN
V
UVLO
I
Q
I
SHDN
V
IN
falling
I
OUT
= 0
I
OUT
= 300mA
T
A
= +25°C
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
V
SET
1.200
CONDITIONS
MIN
2.5
2.25
82
96
0.1
TYP
MAX
5.5
2.47
136
1
UNITS
V
V
µA
µA
mA
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
5.0
1.258
±100
V
V
mV
nA
%
%
1.229
185
±20
Dual Mode is a trademark of Maxim Integrated Products, Inc.
[font=Tahoma, Helvetica, SimSun, sans-serif][size=5][color=#ff0000]libexec/gcc/arm-linux-gnueabihf/4.9/cc1: error while loading shared libraries: libz.so.1: cannot open shared object file: No such fil...
[i=s]This post was last edited by Marsham on 2021-9-8 16:50[/i]I have never used TI chips before. After looking at the examples, I found that both callback and blocking require active reading of data,...
[i=s]This post was last edited by Digital Leaf on 2019-4-22 21:04[/i] [size=4] I am really happy to have the opportunity to participate in this reading month event. Just like the theme says, "Read a g...
We have previously learned about the powerful serial communication module of the MSP430 microcontroller (see "The Differences among the Serial Communication Modules USART, USI, USCI and eUSCI in MSP43...
The ADCs used in the projects I have worked on are all on-chip ADCs of DSP. The advantage of using on-chip ADCs is that they have fast conversion speeds and save costs, which are advantages over off-c...
The S3c2440A supports a 4-channel controller located between the system bus and the peripheral bus. Each DMA controller channel
Unrestricted execution of data movement between devices on the system b...[Details]
It is reported that TuSimple's L4 driverless truck fleet, a provider of autonomous driving solutions, successfully completed China's first platoon following test based on C-V2X vehicle-road collabora...[Details]
You will often see the following instructions in arm-linux assembly:
.align n
means to align the following code according to certain rules. There are two options for the alignment value of the .alig...[Details]
2.80c51 serial port structure 2.1. Introduction to internal structure The internal structure of the serial port of the AT89S51 microcontroller is shown in the figure below. It has two physically in...[Details]
Sewage flow meter selection Sewage flowmeter is one of the more difficult instruments to use, and its selection is also very difficult. The difficulty of selection is not only because of the stro...[Details]
Nothing is perfect, and oscilloscopes are no exception. Digital oscilloscopes have always had a problem that manufacturers are reluctant to mention, and I'm afraid many veteran engineers don't pay ...[Details]
According to foreign media reports, on January 2, local time, Eyesight Technologies and Grupo Antolin announced that they have established a partnership to provide driver and seat occupancy monitorin...[Details]
0 Introduction
Language compression technology not only saves storage space, but also reduces the bandwidth occupied during transmission. The rapid development of digital signal processing...[Details]
Recently, Professor Zhou Peng's team from the School of Microelectronics at Fudan University discovered the principle bottleneck that restricts silicon-based flash memory technology for mainstream ch...[Details]
On October 9, Guoxuan High-tech Co., Ltd. (Guoxuan High-tech) and Sumec Co., Ltd. (Sumec) signed a strategic cooperation agreement. The two parties will carry out all-round cooperation in the field...[Details]
Here we use PCF8591 ADDA chip, 51 single-chip microcomputer, and a potentiometer. By controlling the potentiometer, PWM wave is generated to control the rotation of the servo. And the angle is displa...[Details]
With the trend of breakthrough integration of artificial intelligence, 5G, and IoT, various regions are accelerating the construction of smart cities, and urban security is deepening its development...[Details]
CES (International Consumer Electronics Show), as a global event showcasing the latest technology products and technologies, is attracting more and more companies to participate. As electronic produc...[Details]
Installation
After the electroplating rectifier is placed in place at the production site, connect the copper busbars of the rectifier and the reversing switch. The reversing switch needs t...[Details]
The three main forms of temperature sensors are thermocouples, platinum resistors and thermal resistors
. Thermocouples are welded from two different metal wires, such as NiCr-Ni (type K)...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
