52080100 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wire/cable> 52080100

52080100: DescriptionGM 7 COUNTER NUTS, PLASTIC; CategoryWire/cable; File Size2MB，164 Pages; ManufacturerBOPLA; Environmental Compliance

Download Datasheet Parametric View All

52080100 Overview

GM 7 COUNTER NUTS, PLASTIC

52080100 Parametric

Parameter Name	Attribute value
Accessory type	countersunk nut
Supporting products/related products	PG7 Thread - Explosion Proof Sealed Cable Gland
Material	Polyamide (PA), nylon
characteristic	-

Preview

Download Datasheet

View All

Enclosures . . .

. . . for Industry

A Phoenix Mecano Company

Choosing an Enclosure

GENERAL

CONSIDERATIONS

Generally, enclosures are intended to protect their contents from outside risks. These risks can be varied in

nature and are of extreme importance when choosing an enclosure. In judging whether a particular housing

meets the protection requirements of your application, a clear analysis of the environment where the enclosure

is to be used should be made.

The following conditions need to be taken into account:

1. Protection against contact with and penetration by foreign bodies;

2. Protection against water ingress;

3. Protection against external or internal radiated noise (RFI Shielding);

4. Chemical resistance;

5. Temperature resistance;

6. Impact resistance;

7. Corrosion resistance.

In electronics/electrical engineering, the functions of enclosures are two-fold:

1. To protect the contents from mechanical risks and radiated noise from the outside.

2. To protect the environment from mechanical and electrical risks, as well as from radiated noise

caused by installed components.

With the ever-increasing development of electronic components, the increased packing densities on printed

circuit boards, and the increased "contamination" of the environment by electromagnetic interference, electro-

magnetic compatibility is becoming an issue of growing importance in the choice of an enclosure.

MATERIAL

CONSIDERATIONS

In most applications, material is a major factor in your choice of an enclosure. In general, aluminum is

ideal for EMI/RFI applications; fiberglass is ideal for caustic environments and salt-water applications; polycar-

bonate is good for all indoor and light outdoor applications; and ABS is well suited for indoor

instrumentation designs.

Rose

Bopla enclosures are classified under the generally applicable European protection guidelines of

EN 60529 and IEC 144. These protection classifications are indicated by a designation consisting of two

unchanging letters, IP, plus two digits for the protection grade. Many of the enclosures in this catalog bear the

IP 66 or IP 65 protection classification.

IP 65: Protection against ingress by dust and water jets

IP 66: Protection against ingress by dust and powerful water jets

Specific product lines are classified according to UL 50 and UL 508. These include aluminum, fiberglass, and

plastic. Also noted in this catalog are recommended classification types like NEMA and UL, which are com-

monly used in the USA. Please contact the appropriate association or agency for complete infor-mation

regarding test requirements and qualifications. Refer to the Technical Information Chapter in this catalog for

more information on Protection Classifications.

PROTECTION

CLASSIFICATIONS

TEMPERATURE

RESISTANCE

CORROSION

RESISTANCE OF

ALUMINUM

ENCLOSURES

IMPACT

RESISTANCE

The temperature resistance of enclosures is defined as the maximum permanent temperature at which

the stability of the shape and the protection classification are maintained. Permissible short-term peak temper-

atures are often considerably higher.

Aluminum enclosures are resistant to corrosion even without a special surface treatment. The use of

aluminum alloys with a low copper content increases corrosion resistance. Additional treatments such as irridit-

ing, painting, powder-coating, or a combination of irriditing and painting provide increased corrosion resis-

tance.

Impact resistance is a measurement of the maximum impact that will not affect the protection classifi-

cation. The breaking strength is often far greater. Impact resistance for Rose

Bopla enclosures is

determined in an impact test to EN 50014.

www.Rose-Bopla.com

Recommended Resources

OTL power amplifier circuit in transistor radio a

Fan control ladder diagram

Wiring b for changing a three-phase motor to a single-phase parallel capacitor

Making a solar cell phone charger circuit diagram

Motor fixed rotation direction control circuit_1

Ten times rectifier circuit

Digital Circuits and Digital Systems: Experiments and Course Design Training Course: "Digital Circuit and Digital System Experiment and Course Design Training Course" is written based on the basic teaching requirements of the "Digital Circuit and Logic Design" course proposed by the T...; arui1999 Download Centre

AT91SAM7S256 serial port data loss: When the AT91SAM7S256 serial port receives instructions to send multiple frames of data, the last frame always loses two bytes of data! It is sent normally without serial port instructions, and no dat...; djk0125 Microchip MCU

Using DSP motor speed measurement and detailed explanation: AbstractAcceleration, deceleration and stop functions are realized by pressing buttons, speed is measured by interruption, and software delay is used to eliminate jitter. For the specific implementati...; 灞波儿奔 Microcontroller MCU

Low-power Qorvo chips enhance connectivity and reliability for new Luna smart home system: The smart home system has been developed for so many years, but its positioning is still relatively high. Ordinary families still have a long way to go before they can move in this direction. . . . . ...; btty038 RF/Wirelessly

Highlights of Bluetooth Mesh Technology: Bluetooth is one of the most dominant low-power wireless technologies today and is very familiar to wireless device users and developers. Prior to last summer, Bluetooth network types were limited to ...; 朗锐智科 RF/Wirelessly

ST NUCLEO-G071RB evaluation serial port printing and LED flashing: [i=s]This post was last edited by Jack Zhang on 2020-1-3 17:04[/i]Test a cost-effective MCU . This MCU is definitely a must-have sword for embedded engineers. The most amazing thing is that ST company...; 张jack stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components